- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Re: inter vlan routing on a 5500g
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2010 06:29 AM - last edited on тАО11-27-2013 12:33 AM by Maiko-I
тАО10-22-2010 06:29 AM - last edited on тАО11-27-2013 12:33 AM by Maiko-I
inter vlan routing on a 5500g
I have 3 vlans and interfaces setup on a 5500g switch
vlan1 interfae 192.168.0.220
vlan2 interface 192.168.2.1
vlan3 interface 192.168.1.1
vlan1 port 25 is configured a trunk and connected to a 4400
vlan3 port 27 is configured link access
workstation is connected to port 27 with ip address of 192.168.1.2 and gateway of 192.168.1.1
workstation can ping all 3 interfaces but cannot ping through vlan1 on the 4400.
any suggestions. is the problem local to this switch or something on the 4400?
P.S. This thread has been moved from ProCurve / ProVision-Based to Comware-Based - Hp Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-17-2011 02:59 PM
тАО01-17-2011 02:59 PM
Re: inter vlan routing on a 5500g
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2011 02:59 AM
тАО01-18-2011 02:59 AM
Re: inter vlan routing on a 5500g
You shouldn't need to use OSPF or RIP for this to work because the 5500 will automatically route between local VLAN interfaces.
Two other things to consider:
1) On the trunk port, have you specified the vlans that are allowed? It is not sufficient to just do "port link-type trunk"...you need to follow that with "port trunk permit vlan 1 2 3" or "port trunk permit vlan all". I am not familiar with 4400's but make sure they are both using 802.1Q encapsulation.
2) Have you specified the correct vlan when setting the access port?
e.g:
port link-type access
port access vlan 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-19-2011 09:37 AM
тАО01-19-2011 09:37 AM
Re: inter vlan routing on a 5500g
Look at your IP routes and be sure that all of youe VLAN routes are showing. If the VLAN isn't up for some reason then the route will not appear in your routing table.