Comware Based
cancel
Showing results for 
Search instead for 
Did you mean: 

problem radius authentication (NPS) for an H3C Switch S3600-SI

Candema1
Occasional Advisor

problem radius authentication (NPS) for an H3C Switch S3600-SI

Hello, I have a problem radius authentication (NPS) for an H3C Switch S3600-SI. I have an Access-Reject (3) information on the Radius server with Wireshark. In the Access-Request information, I have information, vendor specific (26), v: Huawei Technology Co, Ltd (2011). Huawei connect-ID (26): 8

I added in request Radius, a vendor-specific (26) with vendor-code (2011) but I do not know what to put in configure attribute.

Do you have a solution to my pb?

thanks

Mathieu

4 REPLIES
johnk3r
Respected Contributor

Re: problem radius authentication (NPS) for an H3C Switch S3600-SI

Hello!

How is your switch configuration?

I recommend you use NTRadPing to validate the configuration of your Radius server.

**************************************
ATP FLEXNETWORK V3 | ACSA
Candema1
Occasional Advisor

Re: problem radius authentication (NPS) for an H3C Switch S3600-SI

Hello,

There is my configuration:

H3C Comware Platform Software
Comware Software, Version 3.10, Release 1702P44
Copyright (c) 2004-2013 Hangzhou H3C Technologies Co., Ltd. All rights reserved.
H3C S3600-28P-PWR-SI

 sysname H3C
#
radius scheme system
radius scheme radius1
 server-type extended
 primary authentication 172.24.3.51 key cipher $c$3$7LB8/u/L8nqGThpfUrRoQZtnBz9WlZwz66QM
 primary accounting 172.24.3.51 key cipher $c$3$dX2eVvAe7Y0fT6yIt/yh14b8NDqXLfITDR27
#
domain system
 authentication radius-scheme radius1 local
 authorization local
 accounting radius-scheme radius1 local
#
local-user admin
 password cipher $c$3$BI/qC84VEaBDx7oPbWjT+r6ZFjqOIv9BqlsN
 service-type ssh telnet terminal
 level 3
local-user read
 password cipher $c$3$+WbSrqtii4TLaFFkeFSlk8hiznxTXuZhZZYk
 service-type ssh telnet terminal
 level 1
#
vlan 1
#
interface Vlan-interface1
 ip address 172.24.3.15 255.255.255.0
#
interface Aux1/0/0
#
interface Ethernet1/0/1
 poe enable
#
interface Ethernet1/0/2
 poe enable
#
interface Ethernet1/0/3
 poe enable
#
interface Ethernet1/0/4
 poe enable
#
interface Ethernet1/0/5
 poe enable
#
interface Ethernet1/0/6
 poe enable
#
interface Ethernet1/0/7
 poe enable
#
interface Ethernet1/0/8
 poe enable
#
interface Ethernet1/0/9
 poe enable
#
interface Ethernet1/0/10
 poe enable
#
interface Ethernet1/0/11
 poe enable
#
interface Ethernet1/0/12
 poe enable
#
interface Ethernet1/0/13
 poe enable
#
interface Ethernet1/0/14
 poe enable
#
interface Ethernet1/0/15
 poe enable
#
interface Ethernet1/0/16
 poe enable
#
interface Ethernet1/0/17
 poe enable
#
interface Ethernet1/0/18
 poe enable
#
interface Ethernet1/0/19
 poe enable
#
interface Ethernet1/0/20
 poe enable
#
interface Ethernet1/0/21
 poe enable
#
interface Ethernet1/0/22
 poe enable
#
interface Ethernet1/0/23
 poe enable
#
interface Ethernet1/0/24
 poe enable
#
interface GigabitEthernet1/1/1
#
interface GigabitEthernet1/1/2
#
interface GigabitEthernet1/1/3
#
interface GigabitEthernet1/1/4
#
 undo irf-fabric authentication-mode
#
interface NULL0
#
 voice vlan mac-address 0001-e300-0000 mask ffff-ff00-0000
#
 ip route-static 0.0.0.0 0.0.0.0 172.24.3.1 preference 60
#
 ssh authentication-type default all
#
user-interface aux 0 7
user-interface vty 0 4
 authentication-mode scheme
#
return

What is the username to fill in NTRADPING?

My Radius server run with HP Procurve, 5130, 3600 V2, A5500

Thanks

16again
Respected Contributor

Re: problem radius authentication (NPS) for an H3C Switch S3600-SI

Look into windows event log, it might give you clues what goes wrong

Candema1
Occasional Advisor

Re: problem radius authentication (NPS) for an H3C Switch S3600-SI

Hello,

I still have the problem, how to test with NTRADping the switch connexion please?

Thanks

Mathieu