Quite a few SAM fixes... I am not sure if any apply to your issue.
11. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, when the user changes a port's
mode to LACP/FEC_AUTO from MANUAL, if there is IP or
any other protocol logged on to the port, no error
message is displayed and the
/etc/rc.config.d/hp_apaportconf file is updated.
12. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, no error message is displayed if
a link aggregate is configured with a valid IP address
but an invalid subnet mask.
13. In the terminal version of SAM, on entering the
SAM -> Networking and Communications -> Autoport
Aggregation sub-area, the attributes of a port in
the "modify" screen are displayed in an incorrect
order.
14. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, when a user configures a link
aggregate, SAM displays a syntax error message.
15. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, whenever a port is removed from
or added to a link aggregate, the following error
message is displayed:
ERROR MESSAGE:
ERROR: lan902 interface | -X -g 902 0 902 :
Error: LinkAggregate 902 is already enabled (LINK_UP)
16. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, SAM modifies the
/etc/rc.config.d/hp_apaconf file despite the failure of
the "Configure Link aggregate" task.
17. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, redundant error messages are
displayed when the "Modify Network Physical Port
Attributes.." action fails.
18. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, no warning or error message is
displayed when a user selects a port with different
Group capability in the "Add or Delete Network
Physical Port" screen.
19. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, SAM disables "Modify Network
Physical Port Attributes.." action item when a user
selects a port in the LACP_AUTO link aggregate.
20. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, no warning or error message is
displayed when a user assigns invalid Port Priority
for a port in the "modify" screen.
21. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, no warning or error message is
displayed when a user assigns invalid Group Capability
for a port in the "modify port" screen or a link
aggregate in the "configure link aggregate" screen.
22. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, no warning or error message
is displayed when a user assigns an invalid IP address
to a link aggregate in the "configure link aggregate"
screen.
23. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, no warning or error message is
displayed when a user assigns an incorrect key for a
port in the "modify port" screen.
24. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, SAM disables the "add" (<) btn,
which is used to add the eligible ports with non-zero
group capability into a link aggregate with zero group
capability and status DOWN.
25. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, when a user assigns the same IP
address to a link aggregate which has been assigned
to another interface, the above action fails but
/etc/rc.config.d/netconf is modified.Also, SAM calls
the "ifconfig" command evenif a user does not modify
the IP address or subnet mask.
26. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, no warning or error message is
displayed when a user selects LACP_AUTO mode port for
addition to the FEC_AUTO link aggregate in the
"Add or Delete Network Physical Port" screen.
27. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, when a user adds a port to a
link aggregate or deletes a port from a link aggregate
through the "Add or Delete Network Physical Port"
screen, the port priority field is not displayed on the
screen.
28. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, when a user deletes a port from
or adds a port to a MANUAL link aggregate, the group
capability value for the link aggregate is deleted from
/etc/rc.config.d/hp_apaconf file.Also, if a user adds a
port with non zero group capability value into a link
aggreagte with zero group capability and in DOWN state,
the group capability value for the link aggregate in
/etc/rc.config.d/hp_apaconf file is incorrect.
29. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, when a user deletes a port from
the FEC_AUTO/LACP_AUTO link aggregate, the
/etc/rc.config.d/hp_apaconf file is modified.
30. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, SAM does not disable the add
button (<) when a MANUAL port is selected for addition
to a LACP_AUTO link aggregate.
31. In SAM -> Networking and Communications -> Autoport
Aggregation sub-area, the "Advance Option" button is
not disabled for MANUAL link aggregate after ports
are added to link aggregate through the "Add or Delete
Network Physical Port" screen.
Berlene
http://www.mindspring.com/~bkherren/dobes/index.htm
