- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Giveing error
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2001 06:41 AM
тАО05-31-2001 06:41 AM
Giveing error
hi all
i have a DDS3 tape drive in HP E-45,with HPUX 10.20 loaded on to it. the required DDS3 patches are loaded.when i am trying to copy some file on to the tape it gives < hardware path of the tape> unable perform close opration and exits.This problem comes only when i use DDS3 dats but is i use any other DAT DDS/DDS2 dat it goes through without any problem. where could be the problem?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2001 06:47 AM
тАО05-31-2001 06:47 AM
Re: Giveing error
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2001 06:47 AM
тАО05-31-2001 06:47 AM
Re: Giveing error
Have you got online diagnostics?
software.hp.com/SUPPORT_PLUS/
install and issue a
tools->info->run on the HW path of the DDS drive. This should give you the model type, f/w and s/w.
Later,
Bill
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2001 06:58 AM
тАО05-31-2001 06:58 AM
Re: Giveing error
If you do the command; ioscan -fkCtape
Does the description of your tapes drive say its an;
HP C1533A (which is a DDS 2)
HP C1537A (which is a DDS 3)
The important bit is it should say HP in the description, as this means its got HP firmware loaded so its compatible with HP servers trying to talk to it.
Then if you do the command; lssf /dev/rmt/?m
It should say;
stape card instance 1 SCSI target 1 SCSI LUN 0 at&t best density available at address ??? /dev/rmt/XX
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2001 07:15 AM
тАО05-31-2001 07:15 AM
Re: Giveing error
I think the problem is that you are using a non compatible Tape Drive and the Media . Please check for the Drive type , it has to HP DDS3 for the Unix machine , sometimes the ones used in Netservers are used in the Unix Boxes too. Also please do check the media type .
Manoj Srivastava