- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- k420 not booting up from cdrom
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2001 04:49 AM
тАО07-05-2001 04:49 AM
when we do a sea ipl we can see the cdrom drive on boot we change the boot up to the cdrom, the next thing we get is boot hard, do you want to interact, no is entered and we get boot from the cdrom address with INSTALL.
after this it hangs and we have the INIT cc03 error, has anyone any idea how to get past this, other than calling an engineer out.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2001 04:56 AM
тАО07-05-2001 04:56 AM
SolutionAre there any panic messages or dump messages?
when you do the SEA try to boot from the HW address as follows:
SEA
P0 8/0.6.0
P1 8/0.5.0
P2 10/12.2.0
let's just say that the P2 is the cdrom
BO 10/12.2.0
record any messages and post them up.
Can you boot from any other path successfully?
Have you got any other Bootable CD?
Is all the h/w powered on?
Later,
Bill
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2001 05:06 AM
тАО07-05-2001 05:06 AM
Re: k420 not booting up from cdrom
are you using "core os " cd,if so check the power connection to all devices, if so change the installaion cd and proceed with installation.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2001 07:11 AM
тАО07-05-2001 07:11 AM
Re: k420 not booting up from cdrom
We are booting from the hpux 11.0 core cd
All devices are powered on
it tries to boot from cdrom then has a panic showing the following error: resettig scsi ibolt:20113 bus6
reset detected ibolt:20113 bus6
system panic
9245xb HP-UX (b.10.20)#1: the current date
panic (display==0xb800,flags==0x0)I/O
after this it tries to boot from the internal disks. We even tried a new core disk just incase the one we had was U/S and still have the same problem.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2001 08:01 AM
тАО07-05-2001 08:01 AM
Re: k420 not booting up from cdrom
1. Power off
2. Power on
3. After hardware tests, type return when prompt to do.
4. In ISL level, type SEA ( Search ).
5. bo from the cdrom path.
Good luck.
Magdi
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2001 07:12 PM
тАО07-09-2001 07:12 PM