- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Array Configuration Utility
Disk Enclosures
1752777
Members
6374
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2000 04:00 PM
тАО12-27-2000 04:00 PM
Array Configuration Utility
I have a 3200 Array controller installed and configured in a Proliant 3000 Windows 2000 box. The disk array controller has been setup and configured correctly through smart start 4.90. The problem is when I try to view the configuration of the array controller through the Array Configuration Utility in Windows 2000 - it starts up and says "detecting array controllers" and just sits at this screen and goes no further. The windows 2000 box has the picked up the 3200 under SCSI Devices and Raid Controllers in Device Manager. I have downloaded the latest RAID Array drivers from COMPAQ's site and also the latest version of the Array configuration utility (2.50.66), but the same behaviour occurs. Any ideas?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2000 04:00 PM
тАО12-27-2000 04:00 PM
Re: Array Configuration Utility
Did you install our Win2K SupportPaq (driver kit) before the ACU or at the same time? (Basically - are you using our drivers or Microsoft's?)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2000 04:00 PM
тАО12-27-2000 04:00 PM
Re: Array Configuration Utility
Upgrade BIOS the Server and firmware for this controller.
New firmware for this controller located in SP12985
In case of the BIOS verify version.
If Version of the BIOS P09 SP15904
If Version of the BIOS E39 SP14127
New firmware for this controller located in SP12985
In case of the BIOS verify version.
If Version of the BIOS P09 SP15904
If Version of the BIOS E39 SP14127
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP