- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Autoraid 12H
Disk Enclosures
1752754
Members
4986
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Not applicable
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-13-2003 03:06 AM
тАО05-13-2003 03:06 AM
Autoraid 12H
What shall I change to get berst performance????
Overall State of Array = READY
Array configuration:
Active Hot Spare Desired = DISABLED
Auto Include = ENABLED
Auto Rebuild = ENABLED
Rebuild Priority = HIGH
Capacity Depletion Threshold = 0%
Write Working Set Interval = 8640 seconds
Language = ENGLISH
Log Full Warning = DISABLED
Volume Set Partitioning = DISABLED
Format Pattern Fill = DISABLED
Subsystem Type ID = 12
LUN Creation Limit = 8
Maximum LUN Creation Limit = 8
Array SCSI configuration:
Controller X SCSI Address = 0
Controller Y SCSI Address = 1
Write Cache = ENABLED
Read Cache = DISABLED
SCSI Parity Checking = ENABLED
SDTR = DISABLED
WDTR = DISABLED
Terminator Power = ENABLED
Unit Attention = ENABLED
Disable Remote Reset = DISABLED
Secondary Controller Offline = DISABLED
Very Early Busy = DISABLED
Queue Full Threshold = 1952
Maximum Queue Full Threshold = 1952
Simplified Resiliency Setting = Normal
Single Controller Warning = ENABLED
Lock Write Cache On = TRUE
Disable NVRAM on WCE False = FALSE
Disable NVRAM with One Ctrlr = TRUE
Disable NVRAM on UPS absent = FALSE
Force Unit Access Response = 0
Disable Read Hits = FALSE
Resiliency Threshold = 4
Tanks
Overall State of Array = READY
Array configuration:
Active Hot Spare Desired = DISABLED
Auto Include = ENABLED
Auto Rebuild = ENABLED
Rebuild Priority = HIGH
Capacity Depletion Threshold = 0%
Write Working Set Interval = 8640 seconds
Language = ENGLISH
Log Full Warning = DISABLED
Volume Set Partitioning = DISABLED
Format Pattern Fill = DISABLED
Subsystem Type ID = 12
LUN Creation Limit = 8
Maximum LUN Creation Limit = 8
Array SCSI configuration:
Controller X SCSI Address = 0
Controller Y SCSI Address = 1
Write Cache = ENABLED
Read Cache = DISABLED
SCSI Parity Checking = ENABLED
SDTR = DISABLED
WDTR = DISABLED
Terminator Power = ENABLED
Unit Attention = ENABLED
Disable Remote Reset = DISABLED
Secondary Controller Offline = DISABLED
Very Early Busy = DISABLED
Queue Full Threshold = 1952
Maximum Queue Full Threshold = 1952
Simplified Resiliency Setting = Normal
Single Controller Warning = ENABLED
Lock Write Cache On = TRUE
Disable NVRAM on WCE False = FALSE
Disable NVRAM with One Ctrlr = TRUE
Disable NVRAM on UPS absent = FALSE
Force Unit Access Response = 0
Disable Read Hits = FALSE
Resiliency Threshold = 4
Tanks
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-13-2003 03:50 AM
тАО05-13-2003 03:50 AM
Re: Autoraid 12H
Perf is gained from proper bus traffic distribution.
strings /etc/lvmtab
ioscan -fnkC disk
and
arraydsp
leaving 50% of capacity unused (unallocated to luns) so the array will leave most data in R1/0 and not R5.
but if you really want to change some management stuff and gain a tiny bit more:
Active Hot Spare Desired = ENABLED
HS is ACTIVE (used for R1/0 storage)
Auto Include = ENABLED
Auto Rebuild = ENABLED
Rebuild Priority = HIGH
(these options will hurt when a disk fails, redundancy is lost - not data, set this to low so that i/o has priority, not the rebuild.. but you are in N not N+1, so this is your call)
Capacity Depletion Threshold = 0%
Write Working Set Interval = 8640 seconds
This needs statistics turned on and analysis of results...
Controller X SCSI Address = 0
Controller Y SCSI Address = 1
Write Cache = ENABLED
Read Cache = DISABLED
makes no difference, but turn them on anyways.. (this is really for windows compatability)
SCSI Parity Checking = ENABLED
(mmm, leave..)
SDTR = DISABLED
WDTR = DISABLED
ENABLE, ENABLE
Queue Full Threshold = 1952
Maximum Queue Full Threshold = 1952
Simplified Resiliency Setting = Normal
(* ** * * * Careful setting this! see the man page arraymgr!!!!! you can get good perf here, once you shutdown you 12H correctly and have a UPS!!!!
strings /etc/lvmtab
ioscan -fnkC disk
and
arraydsp
leaving 50% of capacity unused (unallocated to luns) so the array will leave most data in R1/0 and not R5.
but if you really want to change some management stuff and gain a tiny bit more:
Active Hot Spare Desired = ENABLED
HS is ACTIVE (used for R1/0 storage)
Auto Include = ENABLED
Auto Rebuild = ENABLED
Rebuild Priority = HIGH
(these options will hurt when a disk fails, redundancy is lost - not data, set this to low so that i/o has priority, not the rebuild.. but you are in N not N+1, so this is your call)
Capacity Depletion Threshold = 0%
Write Working Set Interval = 8640 seconds
This needs statistics turned on and analysis of results...
Controller X SCSI Address = 0
Controller Y SCSI Address = 1
Write Cache = ENABLED
Read Cache = DISABLED
makes no difference, but turn them on anyways.. (this is really for windows compatability)
SCSI Parity Checking = ENABLED
(mmm, leave..)
SDTR = DISABLED
WDTR = DISABLED
ENABLE, ENABLE
Queue Full Threshold = 1952
Maximum Queue Full Threshold = 1952
Simplified Resiliency Setting = Normal
(* ** * * * Careful setting this! see the man page arraymgr!!!!! you can get good perf here, once you shutdown you 12H correctly and have a UPS!!!!
It works for me (tm)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-13-2003 04:01 AM
тАО05-13-2003 04:01 AM
Re: Autoraid 12H
Fully agree with Bill. Very good is that FUA is 0. This means that you have good ARM software installed which turns off Forced Unit Access (12h uses its cache all the time), see http://www3.jpn.hp.com/cgi/service/itrcforum/msg_list_disp.cgi?open_flag=1&mode=0&category=8&msg_id=8953
Also agree that SDTR and WDTR should be enabled.
BTW, why are you asking? Do you have perfomance problems with 12h? Can you explain?
Eugeny
Also agree that SDTR and WDTR should be enabled.
BTW, why are you asking? Do you have perfomance problems with 12h? Can you explain?
Eugeny
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP