Disk Enclosures
1748241 Members
4078 Online
108759 Solutions
New Discussion

Re: Cant LogIn to MSA2312SA

 
Sudhakar Subramaniam
Trusted Contributor

Re: Cant LogIn to MSA2312SA

Yes , its normally shipped with the MSA.

Didey
Occasional Advisor

Re: Cant LogIn to MSA2312SA

Thanks for everybody,

I found cable and successful reset MC without proccess delay

 

thnx again

 

garywang
New Member

Re: Cant LogIn to MSA2312SA

Dear All, If I exchange one of the broken Disks. shall I waiting for the reconstruction completed?and How can I monitor it?

 

Funcshun
New Member

Re: Cant LogIn to MSA2312SA

Hello, im using Putty to try to connect.  when i hit enter some gibberish shows on the screen and then seems like it freezes.  Any idea why i cant connect or gibberish is showing?

My end result is trying to configure IP address for dual controllers and reset passwords.  

thanks!

Johan Guldmyr
Honored Contributor

Re: Cant LogIn to MSA2312SA

Hi, if you get something on the screen that usually means your serial cable is the wrong kind or the settings are wrong (like bitrate, stopbit, etc)
AnkitM
Trusted Contributor

Re: Cant LogIn to MSA2312SA

Hi Felipe.

 

I reckon the issue has been sorted out after we changed the settings for Serial Connection to Below:

 

Bits per second = 115200, Data bits = 8, Parity = None, Stop bits = 1, and Flow control = None.

 

Feel free to email me, if you are still facing any issues with regards to same.

 

Ankit

 

 

Was your question answered correctly? If so, please remember to mark your question Answered when you get the correct answer and award KUDOS! to the person providing the answer. This helps others searching for a similar issue.
Shahul_Technica
New Member

Re: Cant LogIn to MSA2312SA

Hi Ankit,

 

I have successfully replaced the SAS HDD, I cant login to Storage Management Controller through GUI but can able to do the telnet and ssh successfully.

 

Kindly help me to rebuild the replaced HDD and if you could help me to do the rebuilding using ssh console .

 

For you refrence i have attached the status of HDD

 

Location Serial Number         Vendor   Rev  How Used   Type   Size    Rate(Gb/s)  SP Status

-------------------------------------------------------------------------------------------------

1.1      3QN2BYJC00009011L3SR  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

1.2      3QN2C04C00009011JF75  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

1.3      3QN2BZ8C00009011AGH3  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

1.4      3QN2A2AK00009011AFGN  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

1.5      3QN2BYRK00009011ADCM  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

1.6      3QN4HT9N00009109QM5Z  SEAGATE  HPS2 AVAIL      SAS    146.8GB 3.0            OK

1.7      3QN4H2R400009109S27M  SEAGATE  HPS2 AVAIL      SAS    146.8GB 3.0            OK

1.8      3QN2C04L00009011JFL4  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

1.9      3QN2BZBA00009011L3W1  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

1.10     3QN2A4HA00009011AEQZ  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

1.11     3QN2C00W00009011AFTC  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

1.12     3QN2BYRQ00009011AFMH  SEAGATE  0004 VDISK      SAS    146.8GB 3.0            OK

 

Replaced HDD

AnkitM
Trusted Contributor

Re: Cant LogIn to MSA2312SA

Execute below commands from SSH.
# set spares disks 1.6
# set spares disks 1.7

If the Vdisk is in a Critical Status, it will start rebuilding.

If the Vdisk is Offline, it means there are more disk failed then RAID can tolerate. Its a potential Data Loss situation.

 

 

You can check Vdisk status and Rebuilding status by
#show vdisks

 

Was your question answered correctly? If so, please remember to mark your question Answered when you get the correct answer and award KUDOS! to the person providing the answer. This helps others searching for a similar issue.