- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: Command View Update 6.0.2 to 8.0
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-25-2008 04:20 AM
тАО04-25-2008 04:20 AM
I need to update a CV6.0.2 installation to CV8. I searched now for some time, but still some questions left:
1. Since CV7 you need e-licenses for the capacity. The customer is still running 6.0.2. So how do I get the e-licenses? EVA is still under support.
2. What is the best way for the update? Uninstallation of 6.0.2 and new installation of 8.0? What about ISEE and WEBES?
Thanks for advice.
Best regards,
Patrick
Patrick
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-25-2008 04:40 AM
тАО04-25-2008 04:40 AM
Solution2. The release notes say:
""The HP Command View EVA Software Suite 8.0 does not support upgrades from earlier software versions. If you are running a version earlier than 8.0, you must first remove the earlier version, rebootthe server, then install HP Command View EVA 8.0. Use Windows Add/Remove programs to remove the earlier version.""
Oh, by the way: according to some other paragraph, you should install SMI-S after installing WEBES...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2008 08:50 AM
тАО04-26-2008 08:50 AM
Re: Command View Update 6.0.2 to 8.0
thanks for you reply. I found the same passage in the release notes, short after you reply. :)
Do you have any hints about WEBES / ISEE? Anything I have to keep an eye on it? I can remember that ISEE sometimes stopped working after an CV update.
Thanks for you help.
Best regards,
Patrick
Patrick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2008 11:54 PM
тАО04-26-2008 11:54 PM
Re: Command View Update 6.0.2 to 8.0
Webes versions should be compatible with all CVE versions. If you decide to go to the 5.1 version, dont forget to apply also the patch 2.0. The installation log can be found in c:\program files\webeslog dir, so you can check if everything went fine.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2008 01:29 AM
тАО04-29-2008 01:29 AM
Re: Command View Update 6.0.2 to 8.0
thanks for you reply. No questions left.
Best regards,
Patrick
Patrick