- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Configuring FC60 disk arrays
Disk Enclosures
1753868
Members
7057
Online
108809
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-25-2002 11:26 AM
тАО11-25-2002 11:26 AM
Does anyone have step by step instructions to configure two sc10's on an FC60 array? I can see the disks in ioscan but can't in SAM. Could be a senior moment. Thanks.
Any Ideas?
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-25-2002 11:30 AM
тАО11-25-2002 11:30 AM
Solution
Gerry,
There's info in the User's Guide and the Advance User's Guide. You can find them here:
http://www.hp.com/cposupport/manindex/hpsurestor19163_eng_man.html
Pete
Pete
There's info in the User's Guide and the Advance User's Guide. You can find them here:
http://www.hp.com/cposupport/manindex/hpsurestor19163_eng_man.html
Pete
Pete
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-26-2002 01:37 AM
тАО11-26-2002 01:37 AM
Re: Configuring FC60 disk arrays
in /sbin/init.d/
there should be startup scripts to start the ARM daemons.
This allow management of the arrays from the ux box (via SCSI command pass thru)
Note, when running ioscans make sure you run it with the -k option as your system load will be hight otherwise. Only run ioscan without -k when you have added hw online. Two ioscans (without -k) can hang.
Later,
Bill
there should be startup scripts to start the ARM daemons.
This allow management of the arrays from the ux box (via SCSI command pass thru)
Note, when running ioscans make sure you run it with the -k option as your system load will be hight otherwise. Only run ioscan without -k when you have added hw online. Two ioscans (without -k) can hang.
Later,
Bill
It works for me (tm)
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP