- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: Error deleting DR Group on EVA8100
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-05-2009 06:58 AM
тАО03-05-2009 06:58 AM
Error deleting DR Group on EVA8100
Has anyone seen the following error before? I am trying to delete a redundancy group which failed during creation with an error saying there was not enough storage capacity. When I try to delete the group I get this error...
Operation failed!
Invalid object condition for this command.
(Caution: Do not use the Back button to exit this page. Doing so may duplicate the action that produced this page.)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-05-2009 08:11 AM
тАО03-05-2009 08:11 AM
Re: Error deleting DR Group on EVA8100
If you get the same error, try to delete it using SSSU, for example:
DELETE DR_GROUP "\Data Replication\payroll"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2009 08:20 PM
тАО07-04-2009 08:20 PM
Re: Error deleting DR Group on EVA8100
Error: Error cannot delete object. [Invalid object condition for this command.]
Has anyone got any clue?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-07-2009 02:41 AM
тАО07-07-2009 02:41 AM
Re: Error deleting DR Group on EVA8100
How to assign points on this new forum? Click the Kudos Star!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-07-2009 01:05 PM
тАО07-07-2009 01:05 PM
Re: Error deleting DR Group on EVA8100
1. Suspend the working DR Groups
2. Disconnect the DR link (Either disable the DR Link port or zone out)
3. Do a failover for the DR group to be deleted from destination EVA
4. Delete the DR group and delete the vdisk if required
5. Enable the DR link and resume the working DR groups.
Otherwise as larry said we have to try resync the controller's on the destination site to resolve this.LEt us know how it goes.If these doesnot resolve then let us know the CVEVA version and details.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-08-2009 12:20 AM
тАО07-08-2009 12:20 AM
Re: Error deleting DR Group on EVA8100
I think the steps 2 and 3 in Rampy's procedure need to be reversed, as it would not be possible to fail over the DR group if both sides could not communicate.
In our case it was not possible to fail over the DR group, because it's been in a state of logging the transactions; moreover - it was hang in some way - I did not write that all the problems begun from stalling access to the vdisk belonging to this DR group. We have been trying quite a lot actions, including removing DR groups while EVAs were separated. Finally we managed to remove the DR group at the destination side and than we were able to present vdisks (i.e. replicas) to the host. However, after this operation the remaining DR group at the source side is in a state that it knows about it's peer DR group at the destination EVA, which does not exist anymore... If we try to perform 'Remove Member' action from the vdisk level, we get "Unable to find DR Group on remote storage system" error. When we try to delete the whole DR group, we get "Invalid object condition for this command" error.
As we really wanted to get rid of this erratic condition, we restared controllers one by one on both arrays and it did not help. We also were instructed by the HP service to perform a resync operation on both arrays and this also did not resolve the problem.
I think that at this moment the only resort would be to force some delete operation at the controller level and this would have to be performed by sending the commands directly to the controllers, not by regular users' Command View interface.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-24-2010 12:25 AM
тАО11-24-2010 12:25 AM
Re: Error deleting DR Group on EVA8100
But the working EVA2 still has all the CA setup which is a problem, cause we can't delete this part of the setup cause of the same error as mentioned above. And the destination CA disks all says state unknown.
Any1 know how to force remove dr member disks from DR groups, or force remove all the CA setup from a working EVA leaving all source disks intact??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-29-2011 12:51 AM
тАО06-29-2011 12:51 AM
Re: Error deleting DR Group on EVA8100
we have same issue with eva4400 - 6100 replication group, anyone got solution?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-02-2011 08:03 AM
тАО07-02-2011 08:03 AM
Re: Error deleting DR Group on EVA8100
Hi, I hope the Target(DR Side) LUNs are in unpresented condition. This is required to delete the DR Group.
Else we can also disable the Link between DC and DR sites so that all DGs will be marked as "Failed"
At this stage we can delete the DR group but need to delete at both DC and DR sites.
Recently we deleted around 8 DR groups in same ways and found no issues.. Enabled the Link after deleting the DR groups which will bring the DR groups normal state..