- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: Expanding a RAID1 array
Disk Enclosures
1752790
Members
6402
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-16-2002 04:00 PM
тАО09-16-2002 04:00 PM
Expanding a RAID1 array
Hello,
I currently have 2 x 18.2 Ultra2SCSI drives configures as a RAID1 array on a 431 Smart controller, firmware rev - 1.18A.
I would like to replace these drives with 2 x 36GB drives. Can somebody recommend a plan for this please? Is it possible to install the new drives alongside the existing drives, copy the data across and then remove the old drives. Or can I expand the existing array with the new disks?
Thanks for any suggestions,
Mat
I currently have 2 x 18.2 Ultra2SCSI drives configures as a RAID1 array on a 431 Smart controller, firmware rev - 1.18A.
I would like to replace these drives with 2 x 36GB drives. Can somebody recommend a plan for this please? Is it possible to install the new drives alongside the existing drives, copy the data across and then remove the old drives. Or can I expand the existing array with the new disks?
Thanks for any suggestions,
Mat
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-13-2002 02:03 AM
тАО11-13-2002 02:03 AM
Re: Expanding a RAID1 array
Hi,
I think the easier way is to replaced one of them and let the rebuild finishes then replace the other one and when the rebuild finishes you can extension the raid disks so you get the full 36Gb.
I hope it will help you.
I think the easier way is to replaced one of them and let the rebuild finishes then replace the other one and when the rebuild finishes you can extension the raid disks so you get the full 36Gb.
I hope it will help you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-13-2002 01:19 PM
тАО11-13-2002 01:19 PM
Re: Expanding a RAID1 array
What Cesar Vieira is true except on post you will have to run the array config and create a 2nd logical drive since that controller does not support logical drive expansion.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP