- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: FC 60 RAID
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-26-2002 01:15 PM
тАО03-26-2002 01:15 PM
FC 60 RAID
I have a FC 60 disk array configured, I need to identify the physical disks on each LUN. I want to label them so that I can identify the disks etc on each LUN. Can you pl help me out in this?
Thnks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-26-2002 02:55 PM
тАО03-26-2002 02:55 PM
Re: FC 60 RAID
This is done via Expert Tool, part of the Support Tools,(xstm and mstm).
If you are unsure if you have these tools (you may not), ask your local HP Customer Engineer (CE, aka hardware tech), as they should have copies available for free.
Good luck!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-26-2002 10:56 PM
тАО03-26-2002 10:56 PM
Re: FC 60 RAID
# mstm
Select the disk array A5272A and run infomation on it (Tools -> Information -> Run)
Attached is a sample file.
At the middle of the output, a picture is presented describing RAID level, LUN number per each disk.
Hope this helps,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-26-2002 11:37 PM
тАО03-26-2002 11:37 PM
Re: FC 60 RAID
You can also use ARMserver. Type:
amdsp -i
and follow the instructions on this link:
http://www.hp.com/cgi-bin/cposupport/get_doc.pl?SNI=hpsurestor19163&LC=information_storage&Tfile=lpg30007
You can also use amdsp -d to identify disks.
man amdsp for more details.
HTH,
Vince
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-27-2002 04:41 AM
тАО03-27-2002 04:41 AM
Re: FC 60 RAID
Disks and File Systems -> Disk Devices
Mark/heighlight the array controllerand then
Actions -> View more information
Then choose 'Disk module status'.
Select the disk you want to flash (click in small green square), and press 'start'.
Essentialy the same as the other methods, but maybe easier if you are used to SAM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-27-2002 07:57 AM
тАО03-27-2002 07:57 AM
Re: FC 60 RAID
You can use either SAM or STM. If you are using SAM, then go to disk devices and select the controller card. If you choose more info, then it will show you the disk array LUNs, the specific disks and the RAID groups.
You can find out each disk by choosing the LED flash option. You can do this from stm too.
Another thing is if you have the disk array utility installed, then you can identify the disks from that. Again, there is a console port specifically for the FC60 and you can connect a terminal to this and check the array status ( read the manuals).
HTH,
Shiju
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-27-2002 08:25 AM
тАО03-27-2002 08:25 AM
Re: FC 60 RAID
Thanks for the help. I was able to identify the disks. Pl consider this discussion closed. I was trying to allocated points to all of you but , the screen for that was not active.
Thnks
SK
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-27-2002 07:55 PM
тАО03-27-2002 07:55 PM
Re: FC 60 RAID
YOu can also use sam to flash the LED.