- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: FC60 on K570
Disk Enclosures
1753267
Members
5426
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-22-2004 01:35 AM
тАО11-22-2004 01:35 AM
FC60 on K570
Already posted this in HPUX sysadmin, but thought it might be better in the storage forum:
Hello!
Have a K570 running 11.0, with Autoraid 12H. Everything is fine.
Just bought a refurb'd FC60 and SC10 - installed second bus expansion board into K570 with two a3404 fibre cards (bus 12 and 14, I figured better to be on different busses), fibred to FC60, and SC10 is split-bus. I followed the wiring diagram I found in the installation manual (pdf), so physically, it's wired right. I expect to (eventually) configure the 10 36GB disks as a mirror.
I do an ioscan and see the fibre cards, target, and disks, at c6t5d0 and c7t4d0. diskinfo says each disk is 10MB, which I expect for a returned-to-factory-defaults.
However, AM60srvr does not see the array. Rescanned, etc, no luck. Loaded the latest extensions pack HWE1100 B.11.00.0403.3, and also have XSWGR1100 (B.11.00.40) and XSWHWCR1100 (B.11.00.41)
The documentation states that I need XSWHWCR1100 (B.11.00.47) to see the array. Do I need to find that specific pack, or is the 11.00.0403.3 going to do it?
Also, I did a dd against the 10MB lun - c6t5d0 works fine, c7t4d0 LOCKS the dd forever, have to reboot to get rid of it. Is the array in a strange state and that's why AM60srvr doesn't find it? I'm at a loss...
The next thing is to patch everything to the hilt and see if that helps, so in the meantime, I'll be doing that.
thanks!
art k.
Hello!
Have a K570 running 11.0, with Autoraid 12H. Everything is fine.
Just bought a refurb'd FC60 and SC10 - installed second bus expansion board into K570 with two a3404 fibre cards (bus 12 and 14, I figured better to be on different busses), fibred to FC60, and SC10 is split-bus. I followed the wiring diagram I found in the installation manual (pdf), so physically, it's wired right. I expect to (eventually) configure the 10 36GB disks as a mirror.
I do an ioscan and see the fibre cards, target, and disks, at c6t5d0 and c7t4d0. diskinfo says each disk is 10MB, which I expect for a returned-to-factory-defaults.
However, AM60srvr does not see the array. Rescanned, etc, no luck. Loaded the latest extensions pack HWE1100 B.11.00.0403.3, and also have XSWGR1100 (B.11.00.40) and XSWHWCR1100 (B.11.00.41)
The documentation states that I need XSWHWCR1100 (B.11.00.47) to see the array. Do I need to find that specific pack, or is the 11.00.0403.3 going to do it?
Also, I did a dd against the 10MB lun - c6t5d0 works fine, c7t4d0 LOCKS the dd forever, have to reboot to get rid of it. Is the array in a strange state and that's why AM60srvr doesn't find it? I'm at a loss...
The next thing is to patch everything to the hilt and see if that helps, so in the meantime, I'll be doing that.
thanks!
art k.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-22-2004 09:02 AM
тАО11-22-2004 09:02 AM
Re: FC60 on K570
Figured out today that the controllers themselves are not in an ioscan. I'm getting another controller tomorrow, as one of them appears to be locked up.
However, Is it normal for one controller to be bad and take down the entire array?
Again, I see the 10MB default LUN 0 on both controllers, but if I access the second one, the dd locks up. The first one reads/writes fine.
Since it's in factory-default mode, the second controller is passive, so is this part of the problem?
Just weird to see one controller being bad and lose both devices in ioscan.
However, Is it normal for one controller to be bad and take down the entire array?
Again, I see the 10MB default LUN 0 on both controllers, but if I access the second one, the dd locks up. The first one reads/writes fine.
Since it's in factory-default mode, the second controller is passive, so is this part of the problem?
Just weird to see one controller being bad and lose both devices in ioscan.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-22-2004 10:41 AM
тАО11-22-2004 10:41 AM
Re: FC60 on K570
Looks like this is it:
http://www2.itrc.hp.com/service/cki/docDisplay.do?docLocale=en_US&docId=200000071553083
Where do I get an NVSRAM file?
http://www2.itrc.hp.com/service/cki/docDisplay.do?docLocale=en_US&docId=200000071553083
Where do I get an NVSRAM file?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-23-2004 04:38 PM
тАО11-23-2004 04:38 PM
Re: FC60 on K570
OK - I was able to fix the problem by getting into the boot menu, and choosing "patch nvsram". In UserCfg, offset 0x33 should be FD (in hex) so that HPUX can see the controllers.
This is exactly as stated in the URL I posted earlier, the only missing part was which NVSRAM page? UserCfg was mentioned in the Service Manual, where 0x28 bit 3 is 1 sets Ethernet enabled.
Now, I have to have someone physically move the serial cable so I can get the other controller to act the right way :)
How do I get points for answering my own problem?
This is exactly as stated in the URL I posted earlier, the only missing part was which NVSRAM page? UserCfg was mentioned in the Service Manual, where 0x28 bit 3 is 1 sets Ethernet enabled.
Now, I have to have someone physically move the serial cable so I can get the other controller to act the right way :)
How do I get points for answering my own problem?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP