- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Failed hard drive not rebuilding
Disk Enclosures
1752770
Members
4805
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-26-2006 12:48 AM
тАО09-26-2006 12:48 AM
Failed hard drive not rebuilding
Hi guys
After replacing a failed hard drive in a 4345 rack, array does not automatically rebuild itself, instead it gives the error attached. i have upgraded drivers and firmwar, and still no luck. please advise if anyone has seen this error
After replacing a failed hard drive in a 4345 rack, array does not automatically rebuild itself, instead it gives the error attached. i have upgraded drivers and firmwar, and still no luck. please advise if anyone has seen this error
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-26-2006 02:41 AM
тАО09-26-2006 02:41 AM
Re: Failed hard drive not rebuilding
Hi ,
You could probably remove the disk which is replaced for faulty drive and check the stautus of the array.
you can try refixing the cable.
you may need to check the errors from server end as well.
Some of the luns seems to be ok is it all accessible? I doubt whether the iformation is from cache for the raid controller
Which server is connected to. ?
regards
Manoharan
You could probably remove the disk which is replaced for faulty drive and check the stautus of the array.
you can try refixing the cable.
you may need to check the errors from server end as well.
Some of the luns seems to be ok is it all accessible? I doubt whether the iformation is from cache for the raid controller
Which server is connected to. ?
regards
Manoharan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-26-2006 07:47 PM
тАО09-26-2006 07:47 PM
Re: Failed hard drive not rebuilding
Hi,
Once remove the drive, the status of the array stays the same stills shows 'interim recovery mode' status 3.
These are the steps i have taken so far, replaced the entire 4345 rack with a new one, replaced smart array controller as well, updated drivers and firmware, and i still have the same error.
The server is a HP proliant ML 570, i have attached a screenshot of the ACU, as you can see from the shot, the new hard drive is online and available but it doesnt want to assign to array B
Once remove the drive, the status of the array stays the same stills shows 'interim recovery mode' status 3.
These are the steps i have taken so far, replaced the entire 4345 rack with a new one, replaced smart array controller as well, updated drivers and firmware, and i still have the same error.
The server is a HP proliant ML 570, i have attached a screenshot of the ACU, as you can see from the shot, the new hard drive is online and available but it doesnt want to assign to array B
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP