- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: HP AutoRAID 12H - Unable to restore LUN inform...
Disk Enclosures
1752808
Members
5983
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-06-2002 12:06 PM
тАО04-06-2002 12:06 PM
HP AutoRAID 12H - Unable to restore LUN information
I've replaced a controller card in AutoRAID 12H (originally with 2 controllers) and after replacing,my LUN information is lost.Tried to recover LUN information from Array control panel "recover" option but it failed.tried with "arrayrecover" command from the host (which is connected to controller x),this also failed giving an error code 0x5c.can any one help me to get back my LUN information and data.
Everything is Possible with a right hope and attitude
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-28-2002 12:30 AM
тАО06-28-2002 12:30 AM
Re: HP AutoRAID 12H - Unable to restore LUN information
Hi jai , you didnt tell me which controller you replaced andwhat is the reason for replcement.then try to undo the things whichever u did.there may be some firmware mismatch which could have caused this error code , i believe.then try to ioscan -fnC disk on the host and find whether the luns are identified and then use the arraydsp -a .if at all nothing helps u have to recreate ur luns and restore the data from the latest backup.
good luck
regards
good luck
regards
regard
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-28-2002 04:09 AM
тАО06-28-2002 04:09 AM
Re: HP AutoRAID 12H - Unable to restore LUN information
Hello,
You shouldn't have lost your LUN information since you have dual controllers, and if you replace one controller, the LUN information would have remained in the other controller.
Make sure you installed your controller correctly. Make sure there were no bent pins before installing it.
If you have 2 controllers, you can replace the controller online, just remove your controller and install the new controller online. When "Ready" is shown, you can use your AutoRAID. Did this message appear after "Initialising" message?
If "Firmware Needed", you need to copy the firmware from the second controller to the new controller.
HTH,
Vince
You shouldn't have lost your LUN information since you have dual controllers, and if you replace one controller, the LUN information would have remained in the other controller.
Make sure you installed your controller correctly. Make sure there were no bent pins before installing it.
If you have 2 controllers, you can replace the controller online, just remove your controller and install the new controller online. When "Ready" is shown, you can use your AutoRAID. Did this message appear after "Initialising" message?
If "Firmware Needed", you need to copy the firmware from the second controller to the new controller.
HTH,
Vince
Tape Drives RULE!!!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP