- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- MODEL 20 PROBLEM
Disk Enclosures
1753808
Members
7626
Online
108805
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-05-2002 11:31 PM
тАО02-05-2002 11:31 PM
MODEL 20 PROBLEM
I'm facing some problem with a HP model-20 (Nike) RAID Box. The box has 2 SPs and 2 LUNs are configured, one LUN assigned to each SP.
The problem I'm facing is, while working, suddenly the Raid Box gave microcode panic and both the LUNs are not accessible now. Instead of showing "Enabled" status, it shows "ready" status on both the LUNs in the Presentation Menu.
Also, if I select individual disks in the pesentation menu, it shows the status as "Bound. But Not Assigned".It shows no problem with the Raid LUNs configured. It seems like the Raid5 has gone off-line. Is there any way to bring it back to "Enabled" state without losing the data ( I have 90GB of data).
I have tried putting one SP controller at a time with auto-tresspass and Unit auto-assign enabled. But still same problem.
Regards,
SHANKU
HP
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2002 01:19 AM
тАО02-06-2002 01:19 AM
Re: MODEL 20 PROBLEM
Hello,
Try to enter Gridmanager from the other SP. If you see both as ENA, then the other SP is faulty. In any case, call your HP representative for help on this issue.
HTH,
Vince
Try to enter Gridmanager from the other SP. If you see both as ENA, then the other SP is faulty. In any case, call your HP representative for help on this issue.
HTH,
Vince
Tape Drives RULE!!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2002 05:08 AM
тАО02-06-2002 05:08 AM
Re: MODEL 20 PROBLEM
Hi,
I think the diskarray 20 has lost only the RAID5 configuration from it's memory but the data should be there.
-Vijay
I think the diskarray 20 has lost only the RAID5 configuration from it's memory but the data should be there.
-Vijay
"Let us fine tune our knowledge together"
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP