Storage Boards Cleanup
To make it easier to find information about HPE Storage products and solutions, we are doing spring cleaning. This includes consolidation of some older boards, and a simpler structure that more accurately reflects how people use HPE Storage.
Disk Arrays
cancel
Showing results for 
Search instead for 
Did you mean: 

MSA P2000 G3 - Poor performance after the replacement of controller

vmnomad
Visitor

MSA P2000 G3 - Poor performance after the replacement of controller

Hi Community

 

about 4 weeks ago one of the controllers in our MSA failed. During the replacement we had issues when both controllers thought they were owners of the vdisks. We had to power off both controllers to resolve the problem

 

Once the controller was replaced I noticed very slow performance during the storage vmotion. 

 

we have two vdisks:

 

vdisk-1 -    16 x 600GB 10K disks in RAID6

vdisk-2 -    8  x 600GB 10K disks in RAID6

 

Both vdisks are owned by the new controller. 

 

When i move VM from vdisk 1 to vdisk 2 it works as expected. However, when I move the VM in the opposite direction, from vdisk 2 to vdisk 1 it takes 5 times longer. When I run command "show vdisk-statistics vdisk-1" I see about 30MB/s throughput. 

 

The problem started right after the controller was replaced. I have double checked everything I could remember - SAN, paths ,ALUA, VAAI, but results are the same. MSA log has no errors/warnings.

 

HP Support has been useless so far. The only recommendation I received was to change the owner of the vdisk, but I can't stop VMs we ran on this vdisk now.

 

Therefore, I thought I might seek for some advice here.

 

I will really apreciate any idea on where to look for the cause of the problem.

 

 

P.S. This thread ahs been moved from General to Disk Array. - Hp forum Moderator

2 REPLIES
Torsten.
Acclaimed Contributor

Re: MSA P2000 G3 - Poor performance after the replacement of controller

Check if the firmware is TS251R004. (current).

Check also, if the controllers report a problem with the flash card. This may cause a disabled write cache. Usually you see such message in the logs right after a controller boot.

 

Search the web for "c04034890":

 

http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/advisoriesDisplay?javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken&javax.portlet.prp_efb5c0793523e51970c8fa22b053ce01=wsrp-navigationalState%3DdocId%253Demr_na-c04034890-1%257CdocLocale%253Den_US&javax.portlet.tpst=efb5c0793523e51970c8fa22b053ce01&sp4ts.oid=4148358&ac.admitted=139...


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
vmnomad
Visitor

Re: MSA P2000 G3 - Poor performance after the replacement of controller

Hi Torsten. thanks for your ideas.

 

The compactflash is just fine. Me and HP support has double checked all event and logs. 

 

We don't run the latest firmware yet. What I also found out is that when I present volumes from these vdisks to the Windows server the copy process between disks goes really fast. So, now I start to think it has something to do with ESXi/VAAI plugin.