- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: MSA P2000fc G3 shows as a L port status.
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2011 02:40 PM
тАО03-02-2011 02:40 PM
Re: MSA P2000fc G3 shows as a L port status.
As to my question, can I have a MSA1500 and a MSA2000 both connecting to 1 FC HBA on the same server ?
So Say:
port 0 FC HBA 1 on server
Port 1 FC on MSA 1500
Port 2 FC on MSA 2000
Zone 1 Port 0 and port 1
Zone 2 Port 0 and port 2
Config: Zone 1 and Zone 2
(I have more devices attached but this is a simplified version of the question)
Will you see both controllers in the HP ACU on the server as expected and required to configure?
At present port 2 is set to a L and I think this may be the issue ?
Many Thanks
Iain
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2011 09:07 PM
тАО03-02-2011 09:07 PM
Re: MSA P2000fc G3 shows as a L port status.
No, the MSA2000 will not show up in ACU.
You do all the configuring via the MSA2000 web interface.
Yes, do configure one HBA-port and one storage-port per zone. Brocade's recommendation is 'one initiator and one target' in each zone.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-03-2011 04:39 AM
тАО03-03-2011 04:39 AM
Re: MSA P2000fc G3 shows as a L port status.
So am I correct in thinking that 1 single port FC HBA on a server can have 2 different MSA's connected to it (as with the zoneing and config I described ?)and the server will see them both ?
Also is the selective storage presentation configured in the web front end of the MSA 2000 also.
Reg
Iain
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-03-2011 05:13 AM
тАО03-03-2011 05:13 AM
Re: MSA P2000fc G3 shows as a L port status.
The "SSP" for P2000 is most easily done in CLI.
Set all virtual disks to not mapped.
Once the WWNs are detected, adjust the host entries.
CLI# set host-name id
Then present the disks to the hosts:
map volume access rw ports a1,b1,a2,b2 lun
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-03-2011 06:33 AM
тАО03-03-2011 06:33 AM
Re: MSA P2000fc G3 shows as a L port status.
So am I correct in thinking that 1 single port FC HBA on a server can have 2 different MSA's connected to it (as with the zoneing and config I described ?)and the server will see them both ?
Yes the server can see both MSAs if you have a zone with
hbawwn
msa1500wwn
and another zone with
hbawwn
msa2000wwn
you can do it other ways, like have the msa2000 wwn and the 1500 in the same. but if you separate them it makes truobleshooting easier
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-16-2011 05:13 AM
тАО03-16-2011 05:13 AM
Re: MSA P2000fc G3 shows as a L port status.
I changed the port type to point-point on the MSA 200 and they now show as F ports on the SAN switches and I have zones apropriately.
I setup the Host port names from the WWN on the MSA and created my VDisk and Volumes and mapped acordingly.
The issue I now have is the HP MPIO that I upgraded to the MSA 2000 version (W2003) does nto apear to be functioning as I see each volume twice, this makes sense due to multiple paths but I thought the MPIO would take care of this as it has on previous MSA deploys ??.........
Any Help/advice greatly apreciated!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-16-2011 07:47 AM
тАО03-16-2011 07:47 AM
Re: MSA P2000fc G3 shows as a L port status.
great, did you install the MPIO DSM as well?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-16-2011 08:14 AM - last edited on тАО08-25-2011 02:02 PM by Kevin_Paul
тАО03-16-2011 08:14 AM - last edited on тАО08-25-2011 02:02 PM by Kevin_Paul
Re: MSA P2000fc G3 shows as a L port status.
Hey, yeah I did install the MPIO but it apears the wrong one :(
I poped a new poste up adn someone replied maybe you can answer my les question in the below poste:
http://h30499.www3.hp.com/t5/Disk-Array/MSA2000fc-showing-volume-twice-in-windows-disk-managment/m-p/4766045#M37291
As eve many thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-16-2011 11:32 AM
тАО03-16-2011 11:32 AM
Re: MSA P2000fc G3 shows as a L port status.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-18-2011 01:22 AM
тАО03-18-2011 01:22 AM
Re: MSA P2000fc G3 shows as a L port status.
- « Previous
-
- 1
- 2
- Next »