- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: MSA1000 CLI not allowing input of commands
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-21-2007 11:23 PM
тАО10-21-2007 11:23 PM
Re: MSA1000 CLI not allowing input of commands
But before you start, you need to find out if your MSA1000 has one of the early EMUs which had a non-flashable "Flash"-chip - no, I kid you not!
There was a replacement program when the MSA1000 was new - don't know what the current state is.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 12:04 AM
тАО10-22-2007 12:04 AM
SolutionYou can't update via the serial console on the early firmware. I just had to update an MSA1000 that was running firmware 2.xx.
The CLI on that version does work properly, however there isn't a "download firmware" command, that you get in the latter releases.
You'll have to connect the MSA up to a server via fibre, then run the MSA Flash utility, available from the download pages here:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=305215&prodTypeId=12169&prodSeriesId=377751&swLang=8&taskId=135&swEnvOID=1005
Cheers,
Rob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 07:29 PM
тАО10-22-2007 07:29 PM
Re: MSA1000 CLI not allowing input of commands
You spoke about upgrading your firmwar from version 2.? to the latest one. Did you jump straight to version 7.? or did you have to step up?, if so were did you get the older versions of the firmware. I've managed to find version 6.31 on an old compaq ftp server.
What method did you use for the upgrade? the firmware cd or did you use the windows MSA flash utility?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 07:35 PM
тАО10-22-2007 07:35 PM
Re: MSA1000 CLI not allowing input of commands
I went straight from 2.x to 5.20 using the MSA Flash utility, without any problems.
As version 7.00 introduces Active/Active controllers, you might want to avoid this version, until you assess the impact it may have...
Cheers,
Rob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 07:48 PM
тАО10-22-2007 07:48 PM
Re: MSA1000 CLI not allowing input of commands
Cheers
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 07:49 PM
тАО10-22-2007 07:49 PM
Re: MSA1000 CLI not allowing input of commands
Try here instead:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12169&prodSeriesId=377751&prodNameId=305215&swEnvOID=1005&swLang=8&mode=2&taskId=135&swItem=co-47103-1
Cheers,
Rob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 07:51 PM
тАО10-22-2007 07:51 PM
Re: MSA1000 CLI not allowing input of commands
I was been real stupid. The fimware for version 4.48 is available on the main page. My Apologise. Thanks for the help though. Might be back later on this afternoon after I try to flash this MSA. Hopefully it all goes well, now were did I put that Fiber channel card?
- « Previous
-
- 1
- 2
- Next »