- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Ml370 on Slot 6
Disk Enclosures
1753511
Members
5221
Online
108795
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-21-2001 04:00 PM
тАО02-21-2001 04:00 PM
Ml370 on Slot 6
I have the 5302/64 Array Controller it is to be installed in Slot 6
I ran Smart Start 4.90A and the System Config runs fine
and the Array Utility too except at boot up after it is done I don't get
the display "Smart Array Controller 5300......"and the system doesn't see the drives so it can't continue creating the system partition
When i put it in Slot 5 it works great and i get the display and everything.The system was already replaced once we thought slot 6 was bad.The card works,I replaced the SCSI cable and the system is fine but i don't know if it is a slot 6 thing?It needs to be installed in Slot 6 according to CTO
I ran Smart Start 4.90A and the System Config runs fine
and the Array Utility too except at boot up after it is done I don't get
the display "Smart Array Controller 5300......"and the system doesn't see the drives so it can't continue creating the system partition
When i put it in Slot 5 it works great and i get the display and everything.The system was already replaced once we thought slot 6 was bad.The card works,I replaced the SCSI cable and the system is fine but i don't know if it is a slot 6 thing?It needs to be installed in Slot 6 according to CTO
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2001 04:00 PM
тАО04-03-2001 04:00 PM
Re: Ml370 on Slot 6
There are no related problems documented in our database . Please call the Customer Support Center @800.652.6672 .
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2001 04:00 PM
тАО04-30-2001 04:00 PM
Re: Ml370 on Slot 6
I'm having the same problem with a 5300 controller in all of the slots. If I install the NIC in slot 1 or 2 (other bus) the problem is solved.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2001 04:00 PM
тАО05-10-2001 04:00 PM
Re: Ml370 on Slot 6
I had the same problem using Smart start 4.90B. If no logical drives exist you will see the 5300 controller. Create the logical drive by pressing f8 just after initialisation of controller. A Option om Configuration Version 1.48 appears. First select the 5300 to be the boot controller, then create your logical partitions. pg I have six 18.2gbs 2 I raid 1 and 4 I raid 5. Save the configuration. Rebut the system. The 5300 controller display appears and initializes the drives.
I tried to install NT4 but, then had to stop because the controller could only see 1GB out of the 17GB logical drive, I wanted a 4gb partition. Scrapped the system and started again.
To alleviate this, placed a do boot disk and created a 2gb primary do partition and formatted this partition, rebooted.
Started installing Nt4 from boot disks and cd. The bios from the 5300 controller appears and asks to choose which operating system you are installing. eg Windows then choose NT4 or 2000.
You will reach the scan devices screen, it will detect the usual IDE, then install 4.94B 5300 controller driver.
Proceed until you arrive at the partition creation part of the install. You see a 2gb dos partition and a 2 gb unallocated partition. Delete the dos partition and create a 4gb NTFS partition. Continue the installation. Remove both floppy and cd.
After rebooting the system asks which system you are using. Eg Windows, then NT4 or 2000 reboots twice.
After reboot you see the normal nt loading process.
I tried to install NT4 but, then had to stop because the controller could only see 1GB out of the 17GB logical drive, I wanted a 4gb partition. Scrapped the system and started again.
To alleviate this, placed a do boot disk and created a 2gb primary do partition and formatted this partition, rebooted.
Started installing Nt4 from boot disks and cd. The bios from the 5300 controller appears and asks to choose which operating system you are installing. eg Windows then choose NT4 or 2000.
You will reach the scan devices screen, it will detect the usual IDE, then install 4.94B 5300 controller driver.
Proceed until you arrive at the partition creation part of the install. You see a 2gb dos partition and a 2 gb unallocated partition. Delete the dos partition and create a 4gb NTFS partition. Continue the installation. Remove both floppy and cd.
After rebooting the system asks which system you are using. Eg Windows, then NT4 or 2000 reboots twice.
After reboot you see the normal nt loading process.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP