- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: RAID5 cannot start autorecovery
Disk Enclosures
1753774
Members
7568
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-23-2005 08:01 PM
10-23-2005 08:01 PM
RAID5 cannot start autorecovery
Hi All ,
Our Configuration ;
I have HP Proliant DL380, which have Quad Channel Smart Array 6400 Controller. MSA30 Dual Bus Enclosure is conected to that server. There is a RAID5 set on MSA30, it contains 146 GB Hard Disks.
Problem ;
One of the 146 GB Hard disks was failed in RAID5 set. We changed the failed disk with a new one ( same capacity,same speed and smae slot )but controller cannot start auto-recovery. When I go to ACU I see the new disk as off-line and ready to be added to any RAID set. Controller has still 1787 Error Code, means "Drive Array Interim Recovery Mode The following drive should be replaced etc...".
As far as I know, the RAID Controller must detect the replaced disk and immediately start the recovery process.
How can we solve the problem ?
Our Configuration ;
I have HP Proliant DL380, which have Quad Channel Smart Array 6400 Controller. MSA30 Dual Bus Enclosure is conected to that server. There is a RAID5 set on MSA30, it contains 146 GB Hard Disks.
Problem ;
One of the 146 GB Hard disks was failed in RAID5 set. We changed the failed disk with a new one ( same capacity,same speed and smae slot )but controller cannot start auto-recovery. When I go to ACU I see the new disk as off-line and ready to be added to any RAID set. Controller has still 1787 Error Code, means "Drive Array Interim Recovery Mode The following drive should be replaced etc...".
As far as I know, the RAID Controller must detect the replaced disk and immediately start the recovery process.
How can we solve the problem ?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-25-2005 03:17 AM
10-25-2005 03:17 AM
Re: RAID5 cannot start autorecovery
Could it be that Autorecover is set to Disabled? Select the New drive and Rebuild manually
Hot Swap Hard Drives
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP