- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Smart Array Forced Rebuild?
Disk Enclosures
1753642
Members
5090
Online
108798
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-29-2005 11:45 AM
09-29-2005 11:45 AM
Smart Array Forced Rebuild?
Is it possible to force a rebuild of a mirror set for the following condition?
Original mirror set on Proliant 6400.
The 6400 uses SCSI bus 1 targets 0,1
I need this disk to rebuild in a DL380G4.
The problem is on post. The 6i Array Controller see's the disk on Bus 2 target 0.
It wants to rebuild to Bus 1, target 1.
I realize the MetaData on the drive has the array config on it and reports 1,1 as it's missing mirror member.
Is there a way with the HPACU CLI to force a rebuild onto Target 2,1?
A work around I created is to put the drive from the 6400 that was using a SA3200 controller into a DL580 with the imbeddded array controller. If I put the drive with data in 1,0 and a blank drive in 1,1, the 580 would allow a rebuild. Next is to put both drives in the 380 G4 and boot with no problems.
Seems like the 6i firmware will report that it has changed the SCSI ID for a drive that was on 1,0 to 2,0 but it's too dumb to also allow it to mirror to 2,1.
Work around #2 is to use cable the backplane of the 380 to SCSI port 1 on the system board instead of the factory default of 2.
I would still like a CLI solution.
Original mirror set on Proliant 6400.
The 6400 uses SCSI bus 1 targets 0,1
I need this disk to rebuild in a DL380G4.
The problem is on post. The 6i Array Controller see's the disk on Bus 2 target 0.
It wants to rebuild to Bus 1, target 1.
I realize the MetaData on the drive has the array config on it and reports 1,1 as it's missing mirror member.
Is there a way with the HPACU CLI to force a rebuild onto Target 2,1?
A work around I created is to put the drive from the 6400 that was using a SA3200 controller into a DL580 with the imbeddded array controller. If I put the drive with data in 1,0 and a blank drive in 1,1, the 580 would allow a rebuild. Next is to put both drives in the 380 G4 and boot with no problems.
Seems like the 6i firmware will report that it has changed the SCSI ID for a drive that was on 1,0 to 2,0 but it's too dumb to also allow it to mirror to 2,1.
Work around #2 is to use cable the backplane of the 380 to SCSI port 1 on the system board instead of the factory default of 2.
I would still like a CLI solution.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP