- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: VA7100 configuration problem !!!
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2002 05:30 AM
тАО04-26-2002 05:30 AM
VA7100 configuration problem !!!
We have VA7100 array connected rp5470 server, through ioscan all the array disks are shown as claimed. But when "armdsp -i" is executed it doesn't show any output. Even armdiscover also doesn't recognize the array.
When armfmt is tried it gives "invalid array id" error message. Even in the stm also it gives the same above error message.
Any suggestions/solutions......
Thanks
Venky
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2002 05:48 AM
тАО04-26-2002 05:48 AM
Re: VA7100 configuration problem !!!
which steps did you execute before?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2002 06:20 AM
тАО04-26-2002 06:20 AM
Re: VA7100 configuration problem !!!
Try starting and stopping the HAtrigger and the dialdtrigger then restarting them. That should refresh the connection. If it's possible, a reboot will accomplish the same thing.
HTH,
Dave
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2002 06:24 AM
тАО04-26-2002 06:24 AM
Re: VA7100 configuration problem !!!
1. Two Fibre cables were connected to brocade switch from CPU and 2 cables were connected from VA7100 dual controller to brocade switch.
2. Using vfpfmt the array disks were formatted and then initialized again. It gave status as ready.
3. Then from the OS side , tried using "armdsp -i" but it gave no output.
4. Stopped and then started hostagent.
5. Tried using armdiscover but it recognises only internal disks.
6. ioscan shows all the array disks as claimed.
Thanks
Venky
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2002 10:29 AM
тАО04-26-2002 10:29 AM
Re: VA7100 configuration problem !!!
In order for the array to be recognized, you will need to set up the array with LUN 0. This is typically set to 10MB in size. You should have the instructions for the VFP (Virtual Front Panel) that came with the array. This will give you step by step instructions on how to create LUN 0 and prep the array. If not you should be able to locate them on the HP web.
HTH,
Dave
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-01-2002 04:54 AM
тАО05-01-2002 04:54 AM
Re: VA7100 configuration problem !!!
Try running the command
armdiscover -f
Declan