- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- VA7400 and Netware 6 Multipath
Disk Enclosures
1754014
Members
7476
Online
108811
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-05-2003 08:51 PM
11-05-2003 08:51 PM
VA7400 and Netware 6 Multipath
Hi,
We have a customer with seven Netware 6 servers connected throu a single Brocade Silkworm 2800 to a VA7400.
The Brocade switch has three zones, one for tape and a zone for each controller. (Controller1 and Controller2...)
LUN:s in RG1 are published to servers in the zone Controller1 and LUN:s in RG2 are published to servers in the zone Controller2.
We are now about to extend the SAN with an additional switch (StorageWorks 2-16 EL) and install one additional FCA (FCA2210) in four of the Netware servers.
Has anyone of you done such thing before? What to keep in mind?
I cannot find any good documentation about Netware and Multipath on HP's website.
Regards,
David
We have a customer with seven Netware 6 servers connected throu a single Brocade Silkworm 2800 to a VA7400.
The Brocade switch has three zones, one for tape and a zone for each controller. (Controller1 and Controller2...)
LUN:s in RG1 are published to servers in the zone Controller1 and LUN:s in RG2 are published to servers in the zone Controller2.
We are now about to extend the SAN with an additional switch (StorageWorks 2-16 EL) and install one additional FCA (FCA2210) in four of the Netware servers.
Has anyone of you done such thing before? What to keep in mind?
I cannot find any good documentation about Netware and Multipath on HP's website.
Regards,
David
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-06-2003 07:14 PM
11-06-2003 07:14 PM
Re: VA7400 and Netware 6 Multipath
Hi
you should use Q-Logic HBAs (Im not sure but I think the 2210 is a Q-Logic 2340)
The Netware driver for the Q-Logic HBAs has an integrated Autopath funktion.
It works fine in our Environment
(Novell Netware 6 Cluster whith Q-Logic HBAs, VA 7100, VA7110, Brocade 2400 and 2/16EL
you should use Q-Logic HBAs (Im not sure but I think the 2210 is a Q-Logic 2340)
The Netware driver for the Q-Logic HBAs has an integrated Autopath funktion.
It works fine in our Environment
(Novell Netware 6 Cluster whith Q-Logic HBAs, VA 7100, VA7110, Brocade 2400 and 2/16EL
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP