- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- after reinstall hpux ,AutoRaid12H command can't wo...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2006 03:35 PM
тАО01-12-2006 03:35 PM
after reinstall hpux ,AutoRaid12H command can't work normally
command can't work normal,please help
# arraydsp -i
Arrays known to the ARMServer:
No arrays were found by the ARMServer
# arraydsp -a 0000003780B7
arraydsp: The
#
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2006 06:07 PM
тАО01-12-2006 06:07 PM
Re: after reinstall hpux ,AutoRaid12H command can't work normally
Please do the following command.
# amdiscover
or
#armdiscover
Which will enable your system to find the attached storage box.
Also check drivers are installed properly for your HBA, where your storage box is connected.
Also install HP Storageworks COmmand view SDM also.
Let us know the result of the above commands.
Regards,
Shameer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2006 07:59 PM
тАО01-12-2006 07:59 PM
Re: after reinstall hpux ,AutoRaid12H command can't work normally
also, ensure that the patch level is also OK.
kind regards
yogeeraj
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2006 09:11 PM
тАО01-12-2006 09:11 PM
Re: after reinstall hpux ,AutoRaid12H command can't work normally
did you re-install the same version of hp-ux ??
The AutoRaid is not supported for
OS > HPUX 11i vers 1.5
Do you see the AutoRaid LUN's using onconfig ??
Regards
Rainer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2006 09:58 PM
тАО01-12-2006 09:58 PM
Re: after reinstall hpux ,AutoRaid12H command can't work normally
Of course you should check the LUN'S with ioscan on NOT with onconfig
Regards
Rainer