Disk Enclosures
1748219 Members
4241 Online
108759 Solutions
New Discussion

how to configure MSA500g2 through CLI

 
Ravi kumar raju
Advisor

how to configure MSA500g2 through CLI

In my MSA500g2 I am unable to get the cli promt.if I reboot the MSA500g2 it is coming up to Memory Pool Information. Here I have attached the booting log.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2009.11.18 14:15:38 =~=~=~=~=~=~=~=~=~=~=~=

Copyright (C) 2003 Hewlett-Packard Corporation
All rights reserved

Firmware version: 1.40
TSMGR=1.02
Board ID: e11
Intrepid board
Board Revision: 7

RIS Size: 43008
Physical Requests: 4096, size 736
Logical Requests: 4096, size 780
Init Stripe Locks: 128
Dynamic Pool Memory: 15901296

Searching for PCI devices...
Bus Dev Func ID Rev Description
--- --- ---- ---------- ---- -----------
0 0 0 0x00f91014 0x03 IBM Bridge (Quasar)
0 2 0 0xb0600e11 0x02 Compaq SCSI Device
0 3 0 0x00460e11 0x01 Compaq SCSI Device
0 4 0 0x00460e11 0x01 Compaq SCSI Device

Setting all BARs (0xf0000000:0xf7ffffff)...
PCI Memory: ID[0x00460e11].BAR[0]=0xf0000000:0xf01fffff (size=0x00200000)
PCI Memory: ID[0x00460e11].BAR[0]=0xf0200000:0xf03fffff (size=0x00200000)

Initializing Quasar...
PCI Memory: ID[0x00f91014].BAR[1]=0x01000000:0x017fffff (size=0x01000000)
PASSED: Quasar Initialization
Initializing XOR Engine...
DIMM 0: Found 256 MB daughter board

Surge Memory Module Mapping:
Start address: 0xc0000000
Total size: 256 MB
FIFO address: 0xc0000400
FIFO size: 255 KB
XOR pool address: 0xc0040000
XOR pool size: 32768 KB
Xfer pool address: 0xc2040000
Xfer pool size: 32512 KB
Data cache address: 0xc4000000
Data cache size: 192 MB

Setting DIMM CAS latency 2
Beginning Surge self-test

Ignore the following message.
PCI Fatal Error! Bus=0 Dev=2 Func=0 Cmd=0x0c Reg=0x1e Err=0x8300


Surge Memory Module Mapping:
Start address: 0xc0000000
Total size: 256 MB
FIFO address: 0xc0000400
FIFO size: 255 KB
XOR pool address: 0xc0040000
XOR pool size: 32768 KB
Xfer pool address: 0xc2040000
Xfer pool size: 32512 KB
Data cache address: 0xc4000000
Data cache size: 192 MB

Parsing cache user def 0 nvram.
parse_nvram_data: bad nvram contents parsed.

Checking to see if cache PIC is in locked out state.
Done.

cache_pre_init: power_up_batt_status=0x2, batteries_were_left_on=0


Battery PIC information:

Time Stamp: 0x000000002db8da00

Cache Board 0:
PIC Revision: 39
PIC Revision: 39
Battery Status: 0xcc
Battery 1 Charging: 1
Battery 1 Good: 1
Battery 1 Open: 0
Battery 1 Short: 0
Battery 0 Charging: 1
Battery 0 Good: 1
Battery 0 Open: 0
Battery 0 Short: 0
Battery 0 Capacity: 100
Battery 1 Capacity: 100
Battery 0 Voltage: 6431 mV
Battery 1 Voltage: 6147 mV
PIC Control: 0x20

Cache Board 1: Not Present/Accessible.

Running Surge cache area test.
Passed Surge cache area test.
PASSED: Surge Initialization
Allocating 28144 bytes LPRAM for tsmgr_root[0]...
Allocating 28144 bytes LPRAM for tsmgr_root[1]...
Chassis is Intrepid.
GPIO present bits: 0x0000
Controller slot: 1
Parsing backplane (chassis) nvram.
Parsing factory nvram.
Initializing 64320 sectors for data bucket use
Allocating 28144 bytes LPRAM for SMGR_root[0]...
init_cyborg_adapters: calling load_smgr i = 1, mode = 2
Loading SMGR for SCSI BDF #1 ...
Allocating 40847 bytes LPRAM for SMGR (BE) R=0 F=0...addr=0x008d0800
Allocating 133903 bytes SHRAM for SMGR (LE) R=1 F=0...addr=0xc2098000
Allocating 17920 bytes SRAM for SMGR (LE) R=1 F=1...addr=0x98008000
Allocating 28144 bytes LPRAM for SMGR_root[1]...
init_cyborg_adapters: calling load_smgr i = 3, mode = 2
Loading SMGR for SCSI BDF #3 ...
Allocating 40847 bytes LPRAM for SMGR (BE) R=0 F=0...addr=0x008e15a0
Allocating 133903 bytes SHRAM for SMGR (LE) R=1 F=0...addr=0xc20b8c00
Allocating 17920 bytes SRAM for SMGR (LE) R=1 F=1...addr=0x98008000

Enabled INTS: 90000d0e
Memory Pool Information...
Start Address: 0xc5d90
Bytes in pool: 15901296 (0xf2a270)
Bytes available: 7359160
Min. Allocation: 128 bytes

Leaving App. Init - active INTS: 800
Start parse
No secondary controller present, redundancy skipped.
B=0 D=?? L=??? T=???? Bus Reset(Request)[tsmgr/smgrif.c L975]
B=1 D=?? L=??? T=???? Bus Reset(Request)[tsmgr/smgrif.c L975]
B=0 D=00 L=000 T=0000 SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=01 L=000 T=0001 SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=02 L=000 T=0002 SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=03 L=000 T=0003 SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=04 L=000 T=0004 SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=05 L=000 T=0005 SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=09 L=000 T=0009 SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=10 L=000 T=000A SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=11 L=000 T=000B SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=12 L=000 T=000C SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=13 L=000 T=000D SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=14 L=000 T=000E SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=0 D=15 L=000 T=000F SCSI Sel Tmo[tsmgr/smgrintr.c L447]
Bus 0: DrvIds(Drv#)- 8[ 8]
B=1 D=02 L=000 T=0002 SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=1 D=09 L=000 T=0009 SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=1 D=10 L=000 T=000A SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=1 D=11 L=000 T=000B SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=1 D=12 L=000 T=000C SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=1 D=13 L=000 T=000D SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=1 D=14 L=000 T=000E SCSI Sel Tmo[tsmgr/smgrintr.c L447]
B=1 D=15 L=000 T=000F SCSI Sel Tmo[tsmgr/smgrintr.c L447]
Bus 1: DrvIds(Drv#)- 0[16], 1[17], 3[19], 4[20], 5[21], 8[24]
nvram_update_chassis_sn: value passed in was wrong length.
Z390MT4243 : 5A3339304D54343234330000000000000000000000000000
Nile EMU Found: Bus 0, ID PROLIANT 6L7I DB, Version 2.28
Temperature: EMU 26 PS1: 0, PS2: 33
nvram_update_chassis_sn: value passed in was wrong length.
Z390MT4243 : 5A3339304D54343234330000000000000000000000000000
Nile EMU Found: Bus 1, ID PROLIANT 6L7I DT, Version 2.28
SCSI TmO: Req=50bbf0h, D=08h, Op=1Bh, LBA=100h, QTag=8h

Current(running) speed, width params of present Direct Attached SCSI Devices:
(If downshifted, device reported maximum capability is shown!)
B1/D00:U320Q,Wide B1/D01:U320Q,Wide
B1/D03:U320Q,Wide B1/D04:U320Q,Wide
B1/D05:U320Q,Wide B1/D08:U320Q,Wide

Initializing 64320 sectors for data bucket use
After cache config...
Memory Pool Information...
Start Address: 0xc5d90
Bytes in pool: 15901296 (0xf2a270)
Bytes available: 6718068
Min. Allocation: 128 bytes

NVRAM Contents:
backplane:
checksum offset = 108
iteration offset = 60
chassis name =
world wide name = 500805F30012E340
chassis serial num = Z390MT4243
backplane serial num = P34420CHAR40MB
factory:
board serial num = P734C0BX3R507Q

Loading SMGR for SCSI BDF #0 ...
Allocating 40847 bytes LPRAM for SMGR (BE) R=0 F=0...addr=0x00987d80
Allocating 133903 bytes SHRAM for SMGR (LE) R=1 F=0...addr=0xc20d9a00
Allocating 17920 bytes SRAM for SMGR (LE) R=1 F=1...addr=0x98000000
Loading SMGR for SCSI BDF #2 ...
Allocating 40847 bytes LPRAM for SMGR (BE) R=0 F=0...addr=0x00991d20
Allocating 133903 bytes SHRAM for SMGR (LE) R=1 F=0...addr=0xc20fa600
Allocating 17920 bytes SRAM for SMGR (LE) R=1 F=1...addr=0x98000000
Startup complete.

Memory Pool Information:
LPRAM: StartAddress = 0xC5D90 , PoolSize=0xF2A270 , Available=0x6470D4
SHRAM: StartAddress = 0x1000000 , PoolSize=0x1000000 , Available=0xF7EB30


Thanks,
Ravi kumar.R
1 REPLY 1
IBaltay
Honored Contributor

Re: how to configure MSA500g2 through CLI

Hi,
this is not on the CLI, but could help...
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00182750/c00182750.pdf?jumpid=reg_R1002_USEN
the pain is one part of the reality