- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: ra4000 config
Disk Enclosures
1753936
Members
9867
Online
108811
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-23-2005 04:54 AM
тАО03-23-2005 04:54 AM
ra4000 config
I have a RA4000 connected to a DL380. Array config utility 7.20.19 sees the RA4000 and can configure the array's and logical drives. Windows 2003 cannot see the logical drives.
Device manger shows the KGPSA-xx PCI Fiber Channel HBA (with adjunct driver)
What am I doing wrong?
Device manger shows the KGPSA-xx PCI Fiber Channel HBA (with adjunct driver)
What am I doing wrong?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2005 08:45 PM
тАО04-03-2005 08:45 PM
Re: ra4000 config
The KGPSA-xx card are "Fabric" adapterts.
I beleive the RA4000 was loop only? (I do not remeber as I did very little work on the RA4000 series). What kind of switch are you using? Can you see the hba and RA4000 connection on the switch?
Please post information about all of youre infrastructure. (I.e. server os, patchlevel, hba firmwarelevels, hba driverlevels, switch type and so on....)
KurtG
I beleive the RA4000 was loop only? (I do not remeber as I did very little work on the RA4000 series). What kind of switch are you using? Can you see the hba and RA4000 connection on the switch?
Please post information about all of youre infrastructure. (I.e. server os, patchlevel, hba firmwarelevels, hba driverlevels, switch type and so on....)
KurtG
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2005 09:15 PM
тАО04-03-2005 09:15 PM
Re: ra4000 config
If you can see kgpsa, i think problem is with ssp (selective storage presentation) on RA4000. From ACU you have to add host(s) to created logical disk(s).
regards,
Andrzej
regards,
Andrzej
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP