- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Advice on changing RAID Card
Disk Enclosures
1748184
Members
4035
Online
108759
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-21-2003 10:06 AM
05-21-2003 10:06 AM
Advice on changing RAID Card
I have a ML370 G1 with a Integrated Smart Array Controller (ROC Chip), I would like to replace the RAID chip with a 5302 Controller, but would I have to rebuild the server ? or would the new controller configure itself to use the existing set?
Thanks
Thanks
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-21-2003 06:00 PM
05-21-2003 06:00 PM
Re: Advice on changing RAID Card
Hi there;
You can move your drive array set from one controller to the other without rebuilding.
The embedded array controller and the 5302 use different drivers, however.
Which OS are you running?
In a Microsoft environment you can add the controller before moving the drives, run the CSP to install the driver and then down the server.
Move the scsi cable to the 5302 and make sure the controller is set as the boot controller in the F10 bios setup by running the system configuration utility.
In a NetWare environment you can load the driver from floppy after moving the scsi cable and setting the 5302 controller as boot in the F10 setup.
Cheers,
Janine
You can move your drive array set from one controller to the other without rebuilding.
The embedded array controller and the 5302 use different drivers, however.
Which OS are you running?
In a Microsoft environment you can add the controller before moving the drives, run the CSP to install the driver and then down the server.
Move the scsi cable to the 5302 and make sure the controller is set as the boot controller in the F10 bios setup by running the system configuration utility.
In a NetWare environment you can load the driver from floppy after moving the scsi cable and setting the 5302 controller as boot in the F10 setup.
Cheers,
Janine
To get results you've never had before, try something you've never tried before.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP