- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Array 431 Controller
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2010 03:03 AM
тАО06-30-2010 03:03 AM
Array 431 Controller
Question is - if i press F2 - are all Data loss or only the configuration is lost and the array will reload the raid5 again by the next start ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-02-2010 01:25 AM
тАО07-02-2010 01:25 AM
Re: Array 431 Controller
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00300504/c00300504.pdf
It seem to me, that you could have more that 1 drive failed.
Try to power down the server again.
Reseat all drives.
Power on.
If it still doesn't work.
Press F1
Boot from smart start CD, if you can then from USB mem stick.
From the maintenance tab run the ACU.
Check whts wrong.
The post error do tell you wich drives are having trouble.
I would be carefull before pressing F2.
BR
/jag
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-02-2010 01:26 AM
тАО07-02-2010 01:26 AM
Re: Array 431 Controller
Then I don't know any tools, that can restore config and use RAID again.
So you will need to send the disks to a recovery service company.
BR
/jag
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-02-2010 01:55 AM
тАО07-02-2010 01:55 AM
Re: Array 431 Controller
Only chance is to give it to an very expensive data recovery service - i know.
but Thank you very much for your help !
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-02-2010 02:01 AM
тАО07-02-2010 02:01 AM
Re: Array 431 Controller
If reseating 3 and 4 don't get them back. then you're out of luck.
But if you get green light on at least 3 drives, then you can re-enable the disabled logical drives.
If not from the prompt, then at least from the ACU.
BR
/jag