- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Command View --Host not visible
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-19-2007 09:52 PM
тАО04-19-2007 09:52 PM
Command View --Host not visible
I have a HP 10K and ,I installed command view 5.5 server .I have around 5 unix host connected to the array .
After installing server ,I started to install commnad view agent on different host ,the first host on which I installed agent was immediately visible in commnad view GUI ,but as I installed agent on later host ,none of the host become visible in GUI .I had to forcibily add host later ,by option of ADD HOST ,and by given WWN numbers of host .By this way of forcibily adding host not all the information about host like IP address and filesystem is available in command view .How can I possibly get that info in command view ,or how can be host automatically detected in command view ?
I even tried to start and stop the agent on hosts but of no use ...
Thanks in advance ....
Cheers,
Admsnap
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-22-2007 08:40 PM
тАО04-22-2007 08:40 PM
Re: Command View --Host not visible
waiting for any answers...
Thanks in advance....
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-22-2007 11:50 PM
тАО04-22-2007 11:50 PM
Re: Command View --Host not visible
Can you clarify which array you're using...
It sounds like you're talking about an EVA, but there isn't a 10K model.
However from what you've said it sounds like the zoning on your SAN switches isn't set correctly to let the array see the hosts.
Hope this helps,
Regards,
Rob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-23-2007 12:44 AM
тАО04-23-2007 12:44 AM
Re: Command View --Host not visible
iam using HP XP 10000.
The zoning is also correct ,it that even after installing agent on each server ,only the first server (host )is automatically visible in command view GUI....
Admsnap
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-25-2007 05:13 AM
тАО04-25-2007 05:13 AM
Re: Command View --Host not visible
which type fibre switches are using.
1. can you pls send the nsshow output from the switches
Cheers
Moez