- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- ERRO EVA4400 Slave Only
Disk Enclosures
1752422
Members
5708
Online
108788
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-28-2009 12:41 PM
тАО03-28-2009 12:41 PM
ERRO EVA4400 Slave Only
Hello everyone, I have a problem with an EVA4400 (2C 1D), the case is that the initialize one controller connected, and when 'connect the second controller now can not manage.
In CV8.0 I get the WWN - Only slave and right:
Operation Failed
Status code: 8100
I tried to restart, boot to the one you had before with nothing holding me but continues to do the same.
I can help?
In CV8.0 I get the WWN - Only slave and right:
Operation Failed
Status code: 8100
I tried to restart, boot to the one you had before with nothing holding me but continues to do the same.
I can help?
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-28-2009 01:14 PM
тАО03-28-2009 01:14 PM
Re: ERRO EVA4400 Slave Only
Command View only talks to the master controller. If that controller is not working, or not connected, you get that message.
Check the controller status from WOCP, try to reset it.
Check the controller status from WOCP, try to reset it.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-28-2009 01:20 PM
тАО03-28-2009 01:20 PM
Re: ERRO EVA4400 Slave Only
I tried, I did not sign but I get nothing.
Is there any way to inicalizarla or something?
What if it started with a single controller?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-28-2009 01:26 PM
тАО03-28-2009 01:26 PM
Re: ERRO EVA4400 Slave Only
Can you restart or power it off from the WOCP?
Try to remove it from the enclosure and insert it again.
The EVA can work with only one controller, there are two for redundancy.
Try to remove it from the enclosure and insert it again.
The EVA can work with only one controller, there are two for redundancy.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP