- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- EVA 4400 WOCP display doesn't match on CV
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2008 02:56 AM
тАО10-23-2008 02:56 AM
I tried to change the port topology via WOCP on the new EVA4400. But once I took a check on the controller status, it said one of my controller was unknown and I couldn't change the controller config (config controller host port and config controller device port).
It even said that one of the controller failed and I can't 'enable the port pair' even if I've made sure that the cabling config is OK.
Then I came back to the CV and there was no error display on any controller and I can click on those two controllers to see both of the informations.
So, can anyone help me with this problem?
Note that the XCS version is 09003000 and the management firmware is 1.00.00.080211
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2008 03:06 AM
тАО10-23-2008 03:06 AM
Re: EVA 4400 WOCP display doesn't match on CV
I need to change both controller's port topology and I just succeed on one controller. If there's any other way to change the port topology into direct, please let me know. Thnx.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2008 04:54 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2008 11:43 PM
тАО10-23-2008 11:43 PM
Re: EVA 4400 WOCP display doesn't match on CV
Uwe is right. i had the same problems on multiple sites using EVA4400. the fix for this problem was solved following upgrade of firmware to 09004000 and consequent upgrade of WOCP to 1.00.00.080916.
just make sure you upgrade the Controllers' firmware first, then the WOCP.
P.S. The WOCP may not reboot automatically following the firmware upgrade as described in the release notes. just reboot it manually if it does not refresh within half an hour.
James
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2008 11:48 PM
тАО10-23-2008 11:48 PM
Re: EVA 4400 WOCP display doesn't match on CV
did the WOCP already have a non-default IP address before you ran the firmware upgrade? I have see the WOCP behaving very strange running 'out-of-the-box'. After the firmware upgrade, I had to press the // button to get back to the 192.168.0.1 address. On a different system I initialized the EVA first to be able to assign a different IP address - that worked much better after the firmware upgrade !!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2008 12:52 AM
тАО11-03-2008 12:52 AM
Re: EVA 4400 WOCP display doesn't match on CV
Just to inform that everything goes normal after upgrading XCS version and management firmware. Thnx for the helps.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-19-2008 06:16 PM
тАО11-19-2008 06:16 PM
Re: EVA 4400 WOCP display doesn't match on CV
i have having the same problem, could not initialise the storage system and one of the controller is not lit up.
firware version is 0900300
would appreciate if someone can help me on how to upgrade the hsv300 firware.
the instruction says
i cant find this location
In the Navigation pane, select the storage system you want to upgrade. The properties window for the selected storage system opens.
3.
Click Code load. TheCodeLoadStorage System-Page1window opens.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-20-2008 05:38 AM
тАО11-20-2008 05:38 AM
Re: EVA 4400 WOCP display doesn't match on CV
There's where you have the "Code load" button. Press it and choose the folder where you have the firmware.
Do not forget to update management module firmware too.