- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- EVA 8000 controller hangs on "TE:28" when booting
Disk Enclosures
1752300
Members
5150
Online
108786
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-10-2010 06:35 AM
тАО09-10-2010 06:35 AM
EVA 8000 controller hangs on "TE:28" when booting
Our EVA 8000 has recently been moved accross town (11 miles) and then powered on after being powered off for almost a year. When we power it on controller B starts fine, but A hangs for a few minutes on TE:28 before going into failure mode. Neither fan is operaional (these were swapped with B and were verified to be operational) and the yellow LED is lit on them. If we boot the controller with the fans removed it boots right up, likewise if we pull both fans while it is hung on TE:28, it will continue booting up. I opened up the controller and re-seated everything with no luck. We successfully upgraded to 6220 and that didn't help either.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-29-2010 11:54 PM
тАО09-29-2010 11:54 PM
Re: EVA 8000 controller hangs on "TE:28" when booting
If the controller not complete the TEs, the only solution is to replace the Controller itself. proceed to open a case with HP and get the controller replaced.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-03-2010 12:12 AM
тАО10-03-2010 12:12 AM
Re: EVA 8000 controller hangs on "TE:28" when booting
are the cache batteries on both controllers OK?
if not you should first replace them, if OK then you need your controller be replaced.
if not you should first replace them, if OK then you need your controller be replaced.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP