- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: EVAperf and CommandView 3.3.3
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-21-2005 11:11 PM
тАО06-21-2005 11:11 PM
We have 6 x EVA5000 with VCS 3.025.
If it is not possible to run EVAperf with CV 3.3.3, are there any other tools to gain metrics such as IOPS / controller or throughput (in MB/s) ?
Thanks in advance for any help !
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-21-2005 11:53 PM
тАО06-21-2005 11:53 PM
Re: EVAperf and CommandView 3.3.3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-22-2005 01:02 AM
тАО06-22-2005 01:02 AM
Re: EVAperf and CommandView 3.3.3
evaperf is connecting the the MA :
C:\PROGRA~1\Hewlett-Packard\EVA Performance Monitor>evaperf fnh
Verifying access ...
Host Username Accessible
---------------------- ------------- ----------
fnh1ma01 administrator Yes
but "evaperf ls" does not list any of the EVAs :
C:\PROGRA~1\Hewlett-Packard\EVA Performance Monitor>evaperf ls
No EVA systems were found
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-22-2005 02:57 AM
тАО06-22-2005 02:57 AM
Re: EVAperf and CommandView 3.3.3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-22-2005 03:09 AM
тАО06-22-2005 03:09 AM
SolutionI have tried it on a dedicated management server, not an SMA. The SMA uses a different device driver than a normal host and has some tweaks.
The CV-EVA V4 installation guide (T3724-96001) says that EVAperf just needs LUN 0 and this one is always presented by the EVA. It also has some comments for installing EVAperf on the SMA. You apparently need to reboot the SMA.