- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: FC60
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-09-2000 04:52 AM
тАО10-09-2000 04:52 AM
I am installing a new FC60 and is connected to an HP 9000 N-class machine. After installing the server, executing the sam it is showing me only one controller ( controller A) of FC60 and the status of the second ( controller B ) as CRITICAL.
Thanks in advance.
Regards,
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-11-2000 02:46 AM
тАО10-11-2000 02:46 AM
Solutiontry the following (with your devfile, ioscan -fnkClan ):
HP-UX11# fcmsutil /dev/fcms6
Local N_Port_ID is = 0x000001
N_Port Node World Wide Name = 0x1000001083B9A51E
N_Port Port World Wide Name = 0x1000001083B9A51E
Topology = IN_LOOP
Speed = 1062500000 (bps)
HPA of card = 0xF9EFF000
EIM of card = 0xFFFFFFFF
Driver state = READY
Number of EDB's in use = 0
Number of OIB's in use = 0
Number of Active Outbound Exchanges = 1
Number of Active Login Sessions = 3
If the driver state is not Ready, reconnect the fibercable.
Check the kernelvariable num_tachyon_adapters that it match the number of your fc- cards...
regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-11-2000 04:25 AM
тАО10-11-2000 04:25 AM
Re: FC60
Try: ammgr -c AA
Where ARRAY ID is the serial or allias returned when you do: amdsp -i
This will put both controlers in active mode.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-11-2000 05:52 AM
тАО10-11-2000 05:52 AM
Re: FC60
Hope this helps, Udo
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-11-2000 06:27 AM
тАО10-11-2000 06:27 AM
Re: FC60
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-14-2000 01:39 AM
тАО10-14-2000 01:39 AM
Re: FC60
We have found that the 2nd controller was defective ? We are getting a replacement.
Also I would like to know :
What is the command to eanble the read and
write cache of the second controller of the FC60 ?
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-29-2000 09:10 AM
тАО10-29-2000 09:10 AM
Re: FC60
if you have done the correct powerup procedure and see both controllers and all luns in ioscan and optimal in mstm->tools->information, but read and write cache are still disabled, you should contact your local response center. if there are no datas on fc60, the response center can set the fc60 to factory default after checking the fit of cables and the setting of dip switches and full bus or split bus.
regards,
stefan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-07-2000 02:57 AM
тАО11-07-2000 02:57 AM
Re: FC60
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-07-2000 02:58 AM
тАО11-07-2000 02:58 AM