- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: HP Smart array P800 Controller error !
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-07-2008 10:40 PM
тАО07-07-2008 10:40 PM
When I boot up the server I can choose F9 for setup RBSU and I set the Array Controller as primary boot controller, as is instructed in the manual.
Then the Smart Array P800 Controller initializes, but this takes forever...
After that's done, I get the error :
Drive Array Controller Failure
[command failure (cmd=11h err=020h)]
Then I've placed the SmartStart cd in the dvd-drive en it boot's up from it.
At the intro It says :
BootController : Smart Array P800
BootController Disk Size : 0 MB
There I use the Diagnostic Report-tool and what I get is a blanc summary !
PCI Device Information says :
Device 4 : Smart Array P800 Controller
Does it detect the Smart Array Controller or not ??!!
I've tried placing different disks going from SAS to SATA :
2 SAS-disks
2 SAS + 2 SATA
2 SATA
None of above setup makes that disks are detected... and when the Smart Array P800 Controllers initializes it always takes forever without result, exept the error.
I have 18 disk-slots, and a lot of SAS and SATA disks to try... but I can't get RAID configured...
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-08-2008 01:06 AM
тАО07-08-2008 01:06 AM
SolutionAlso try to reseat the Smart Array or move it to another slot. And try disconnecting the SAS cables from the controller.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-08-2008 01:13 AM
тАО07-08-2008 01:13 AM
Re: HP Smart array P800 Controller error !
Yes it's with BBWC.
Perhaps stupid question but how do I disable the BBWC ? Can I do this via RBSU ?
First time I configure a Proliant server...
I encounter many problems...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-08-2008 01:16 AM
тАО07-08-2008 01:16 AM
Re: HP Smart array P800 Controller error !
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-08-2008 02:16 AM
тАО07-08-2008 02:16 AM
Re: HP Smart array P800 Controller error !
I've made a cd with the latest firmware.
When the firmware-program starts it detects all the devices (including the P800 array controller) and it wants to instal the latest firmware/drivers.
Now here's the thing, with the P800 he says :
no driver installed, version 4 available
BUT : I cannot check the square for the driver to instal. When I press the "Check All"-button all is checked, except that for the P800 array controller...
I cannot check it manually...