- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: HSZ70 cluster
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-30-2009 01:58 AM
тАО11-30-2009 01:58 AM
HSZ70 cluster
Hello,
We have a HSZ70 cluster with TRU64 systems. Its a 2 node cluster.
Today we detected an alarm beeping. Also found that one of the disks from the array is showing amber light.
That should not be a problem , becauze we have 2 disks in SPARESET.
But the problem is when we try to connect to HSZ70 from the system command prompt, instead of going to
HSZ70 prompt it is going to FMU prompt?
root@CLUSTER1> /usr/lbin/hsxterm5 -b 0 -t 1 -l 5
HSXterm, Host Port CLI Terminal Emulator - D'Unix Ver 1.20
Copyright 1998, Compaq Computer Corporation
All Rights Reserved
FMU> ?
Your options are:
DESCRIBE
EXIT
SET
SHOW
FMU> exit
So what to do in this case?
Thanx,
Admin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-30-2009 01:15 PM
тАО11-30-2009 01:15 PM
Re: HSZ70 cluster
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-01-2009 08:13 AM
тАО12-01-2009 08:13 AM
Re: HSZ70 cluster
Just do exit, you will then go back to your normal hsz prompt - whatever you have it set to? If you have the last fail and or istance codes you could enter those and get a decode. If it is a faied disk then the repair action code will be 40 or 42 which basically tells you to replace the failed drive which you know already!
No need to use FMU if you are sure you have a disk problem.
You now need to remove and replace the failed drive and delete the failed drive from the failedset. Then add the new drive into the spareset.
Mark...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-01-2009 01:35 PM
тАО12-01-2009 01:35 PM
Re: HSZ70 cluster
Hi,
I am afraid but thats not the solution.
Yes there was a disk failure and we did a replcement already. But the problem is , using hsxterm we used to get the HSZ70 prompt till now.
But now when we do hsxterm , it DIRECTLY goes to FMU prompt and if we give exit here then it comes out on the normal command prompt.
Thats the strangest part. Any guesses what could be the problem?
Or is there any aleternate way to reconfigure scp device or so??
Thanx,
admin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 01:28 AM
тАО12-02-2009 01:28 AM
Re: HSZ70 cluster
I never use HSZterm so no help there.
Just plug a cable directly in the front of the ctrl - works fine for me everytime.
Mark...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 01:31 AM
тАО12-02-2009 01:31 AM
Re: HSZ70 cluster
We use hsxterm5 command to get HSZ70.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 01:32 AM
тАО12-02-2009 01:32 AM
Re: HSZ70 cluster
HSZ70> run fmu
it says fmu is already running ....
So?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 01:56 AM
тАО12-02-2009 01:56 AM
Re: HSZ70 cluster
Assuming that you can - restart the ctrl concerned.
Mark...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 02:09 AM
тАО12-02-2009 02:09 AM
Re: HSZ70 cluster
You mean , restart the controller itself ??
Both the controllers or what?
Please clarify.
Thanx,
admin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 02:27 AM
тАО12-02-2009 02:27 AM
Re: HSZ70 cluster
Assuming that you are not going to interrupt the users - which SHOULD not be a problem if you reboot one ctrl - then the ctrl that you are having the problem with!
However you may wish to do this at a quite period or consult your local maintenace supplier before doing this.
Mark...