- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: How to add new blade server to EVA system thro...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-13-2008 09:19 PM
тАО01-13-2008 09:19 PM
First, will the switch get the wwn of the server automatically? if yes : what will be the problem if it didn't take?
Second, If No then how to add?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-13-2008 11:09 PM
тАО01-13-2008 11:09 PM
Re: How to add new blade server to EVA system through fiber switch
2). You need to fix the problem. You cannot manually 'add' the WWN into the switch's nameserver.
By the way: the EVA will also learn the server's WWN(s) from the switch. While you can enter the WWN manually, I recommend that you don't do it. Let the EVA learn and then you know that the end-to-end connectivity works.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2008 03:29 PM
тАО01-14-2008 03:29 PM
Re: How to add new blade server to EVA system through fiber switch
did you use zoning on your switch. If you did than you have to zone the switch first before the Server will see the EVA.
With regards,
Otto
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2008 09:06 PM
тАО01-14-2008 09:06 PM
Re: How to add new blade server to EVA system through fiber switch
The status is changing from NO-Sync to IN-Sync alternatively.
How to start the troubleshooting? from the server or the SW.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2008 09:57 PM
тАО01-14-2008 09:57 PM
Re: How to add new blade server to EVA system through fiber switch
> The status is changing from NO-Sync to IN-
> Sync alternatively.
I take it there's no operating system on the blade at this point... This can happen because the drivers for the HBA haven't been started up.
Try getting in to the setup for the HBA and Enabling the BIOS, this usually works.
If that fails, then you may well have a cabling or speed issue as mentioned by Uwe.
Cheers,
Rob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2008 09:16 PM
тАО01-15-2008 09:16 PM
Re: How to add new blade server to EVA system through fiber switch
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2008 10:55 PM