- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- How to remove a "ghost" disk from FC60?
Disk Enclosures
1752261
Members
4934
Online
108785
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-14-2003 09:17 PM
12-14-2003 09:17 PM
How to remove a "ghost" disk from FC60?
Hi,
there is an FC60 connected to L3000, running HP-UX 11.00.
First I had 4 SC10s attached to FC60 in the full-bus mode. Then 2 SC10s were removed and two remaining were configured in a split-bus mode. Now amdsp -a gives
SCSI Channel:ID = 2:12
Enclosure = ?
Slot (0-based) = ?
Disk State = NO RESPONSE
Disk Group and Type = 000000000000000000 HOT SPARE
Capacity = 0.0 GB
Manufacturer and Model = NO_VENDOR NO_MODEL
Serial Number = NO_SERIAL_NUM
Firmware Revision = NO_FW_REV
I guess this is a "ghost" from the old 4 SC10 configuration. Initially this disk was configured as a hot spare, but I forgot to remove it when switching to the new configuration.
Is it possible to remove _just this_ entry from the configuration without re-building the whole FC60 shop (as HP recommends)?
All other disks seem to be fine.
Thanks much for help.
Peter
there is an FC60 connected to L3000, running HP-UX 11.00.
First I had 4 SC10s attached to FC60 in the full-bus mode. Then 2 SC10s were removed and two remaining were configured in a split-bus mode. Now amdsp -a
SCSI Channel:ID = 2:12
Enclosure = ?
Slot (0-based) = ?
Disk State = NO RESPONSE
Disk Group and Type = 000000000000000000 HOT SPARE
Capacity = 0.0 GB
Manufacturer and Model = NO_VENDOR NO_MODEL
Serial Number = NO_SERIAL_NUM
Firmware Revision = NO_FW_REV
I guess this is a "ghost" from the old 4 SC10 configuration. Initially this disk was configured as a hot spare, but I forgot to remove it when switching to the new configuration.
Is it possible to remove _just this_ entry from the configuration without re-building the whole FC60 shop (as HP recommends)?
All other disks seem to be fine.
Thanks much for help.
Peter
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP