- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Model 20 Disk Array Service Light
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-28-2003 08:57 AM
тАО01-28-2003 08:57 AM
I have a model 20 disk array system with sp620 contollers. I recently had a controller die. I replaced the controller and the same symptoms occured. This is what happens when the array is booted up, the drives all spin up and show ready. Then the Service light blinks once, thn stays on steady. Inspection of the storage processor lights show the service light lit on the bottom of the two processor cards.
Any Ideas?
-V
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-28-2003 09:11 AM
тАО01-28-2003 09:11 AM
Re: Model 20 Disk Array Service Light
Eugeny
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-28-2003 09:46 AM
тАО01-28-2003 09:46 AM
Re: Model 20 Disk Array Service Light
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-28-2003 10:40 AM
тАО01-28-2003 10:40 AM
SolutionConnection setup 9600/8/N/1
Eugeny
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-28-2003 03:55 PM
тАО01-28-2003 03:55 PM
Re: Model 20 Disk Array Service Light
Have you tried reseating the sp yet? Sometimes you can get lucky...
Hope it helps
John
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-29-2003 03:50 PM
тАО01-29-2003 03:50 PM
Re: Model 20 Disk Array Service Light
Regards, --bmr
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2003 01:54 AM
тАО01-30-2003 01:54 AM
Re: Model 20 Disk Array Service Light
Via xstm tools-info-run or in FE Mode in the presentation manager (Ctrl P, shift F E in presentation screen) Then back to the menu (^) then select UEL.
It could be that you didn't update the SP PRoms after replacement. log into the new SP and select update SP Prom from the SP menu.
Otherwise it's your simms as mentioned. Check in the presenter if caching is enabled.
Later,
Bill