Disk Enclosures
cancel
Showing results for 
Search instead for 
Did you mean: 

Need help add Unassigned Drives to RAID1+0

HPklon
Occasional Visitor

Need help add Unassigned Drives to RAID1+0

Hi.
configuration

(Interim Recovery) Logical Drive 1 (273.4 GB, RAID 1+0) \\.\PhysicalDrive0

Assigned Drives
0 MB SAS Drive at Port 2I : Box 1 : Bay 6
146 GB 1-Port SAS Drive at Port 1I : Box 1 : Bay 1
146 GB 1-Port SAS Drive at Port 1I : Box 1 : Bay 2
146 GB 1-Port SAS Drive at Port 2I : Box 1 : Bay 5

Unassigned Drives
146 GB 1-Port SAS Drive at Port 1I : Box 1 : Bay 3


Failed Drives
0 MB SAS Drive at Port 2I : Box 1 : Bay 6
0 MB SAS Drive at Port 2I : Box 1 : Bay 6

or this conf

Smart Array P400i in Slot 0 (Embedded)
Bus Interface: PCI
Slot: 0
Serial Number: PH73MU3007
Cache Serial Number: PA82C0H9SUE103
RAID 6 (ADG) Status: Enabled
Controller Status: OK
Chassis Slot:
Hardware Revision: Rev B
Firmware Version: 6.86
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 15 secs
Wait for Cache Room: Disabled
Surface Analysis Inconsistency Notification: Disabled
Post Prompt Timeout: 0 secs
Cache Board Present: True
Cache Status: OK
Accelerator Ratio: 25% Read / 75% Write
Drive Write Cache: Disabled
Total Cache Size: 256 MB
No-Battery Write Cache: Disabled
Cache Backup Power Source: Batteries
Battery/Capacitor Count: 1
Battery/Capacitor Status: OK
SATA NCQ Supported: False

Array: A
Interface Type: SAS
Unused Space: 0 MB
Status: Failed
MultiDomain Status: OK

One of the drives on this array have failed or has been removed.

Logical Drive: 1
Size: 273.4 GB
Fault Tolerance: RAID 1+0
Heads: 255
Sectors Per Track: 32
Cylinders: 65535
Stripe Size: 128 KB
Status: Interim Recovery Mode
MultiDomain Status: OK
Array Accelerator: Enabled
Unique Identifier: 600508B1001030303720202020200005
Disk Name: \\.\PhysicalDrive0
Mount Points: C:\ 9.8 GB
Logical Drive Label: A00CA58CPH73MU3007 A50D
Mirror Group 0:
physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK)
physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK)
Mirror Group 1:
physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SAS, 146 GB, OK)
physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SAS, 0 MB, Failed)

physicaldrive 1I:1:1
Port: 1I
Box: 1
Bay: 1
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPDD
Serial Number: 3NM1J8PR00009738QM2X
Model: HP DG146ABAB4
PHY Count: 1
PHY Transfer Rate: 3.0GBPS

physicaldrive 1I:1:2
Port: 1I
Box: 1
Bay: 2
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPDD
Serial Number: 3NM1JBZ700009738D5E5
Model: HP DG146ABAB4
PHY Count: 1
PHY Transfer Rate: Unknown

physicaldrive 2I:1:5
Port: 2I
Box: 1
Bay: 5
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPDD
Serial Number: 3NM0WMCB00009733KGSD
Model: HP DG146ABAB4
PHY Count: 1
PHY Transfer Rate: Unknown

physicaldrive 2I:1:6
Port: 2I
Box: 1
Bay: 6
Status: Failed
Drive Type: Data Drive
Interface Type: SAS
Size: 0 MB

unassigned

physicaldrive 1I:1:3
Port: 1I
Box: 1
Bay: 3
Status: OK
Drive Type: Unassigned Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPDD
Serial Number: 3NM1GHLV00009735T5NE
Model: HP DG146ABAB4
PHY Count: 1
PHY Transfer Rate: Unknown

How do I remove to replace the array is filed physicaldrive 2I: 1:6 on working physicaldrive 1I: 1:3
3 REPLIES
Sudhakar Subramaniam
Trusted Contributor

Re: Need help add Unassigned Drives to RAID1+0

Whats the server model that you have?
Michael A. McKenney
Respected Contributor

Re: Need help add Unassigned Drives to RAID1+0

Usually you go into the raid array hardware configuration at post and add the drive, if it does not add it for you. Do you have room for a hot spare in the server? I would consider adding a spare drive for failover. Then, you add the replacement to the spare as a spare.
HPklon
Occasional Visitor

Re: Need help add Unassigned Drives to RAID1+0

HP DL 360 G5

if i add insert drive in to physicaldrive 2I:1:6 slot - all ok. begining rebuild.

But i need insert drive in to physicaldrive 1I:1:3 slot - fieled rebuild.

Smart Array P400i found physicaldrive 1I:1:3 and offers create new array.

Smart Array P400i can not insert physicaldrive 1I:1:3 in existing array and can not rebuild array