- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- OS(OSR5.07) does not see all of 2nd drive array on...
Disk Enclosures
1753808
Members
8356
Online
108805
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2005 07:04 AM
тАО11-03-2005 07:04 AM
OS(OSR5.07) does not see all of 2nd drive array on 6i cltr.
DLS380,6-134gig drives,6i cltr, 2 drive arrays Raid5. Config arrays in the rsbu array
utility. Booted of SCO boot disk, loaded the ciss btlds. OSInstall saw both drives but only
24 gig of the 268gig second one. No known limits from SCO knowledge base.
Ran mkdev cipqciss, selected options but same
results.
Any ideas?
utility. Booted of SCO boot disk, loaded the ciss btlds. OSInstall saw both drives but only
24 gig of the 268gig second one. No known limits from SCO knowledge base.
Ran mkdev cipqciss, selected options but same
results.
Any ideas?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2005 11:28 PM
тАО11-06-2005 11:28 PM
Re: OS(OSR5.07) does not see all of 2nd drive array on 6i cltr.
The problem is the difference in drive parms
between ORCA & ACU. ORCA sets the logical number of sectors/track at 63, whereas ACU sets it as 32. IF the MAX BOOT parameter in
ACU is enabled, the logical number of sectors/tracks is set to 63; therefor SCO OSR5.x will correctly identify the drive capacity.
between ORCA & ACU. ORCA sets the logical number of sectors/track at 63, whereas ACU sets it as 32. IF the MAX BOOT parameter in
ACU is enabled, the logical number of sectors/tracks is set to 63; therefor SCO OSR5.x will correctly identify the drive capacity.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2005 11:30 PM
тАО11-06-2005 11:30 PM
Re: OS(OSR5.07) does not see all of 2nd drive array on 6i cltr.
close
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP