- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: OSEM does not recognize a managment entity
Disk Enclosures
1748204
Members
3233
Online
108759
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-21-2008 08:49 AM
04-21-2008 08:49 AM
OSEM does not recognize a managment entity
Hi,
I have installed OSEM 1.4.5 on a command view server.
(HP Blade BL460c, HP Management agent installed + SNMP enabled + ISEE installed)
Now I have entered a new system (the CV Server itself)
on the "Managed Systems" tab by entering the IP address of the system and the name.
After I pressed the apply button and switched to the managed systems list, the new system is in list but the additional information e.g. serial number, product number and mac address are empty. On the "valid SN" tab I see two question marks.
A restart of the OSEM service take no effect.
Is the BL460c not supported by OSEM?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-22-2008 07:01 AM
04-22-2008 07:01 AM
Re: OSEM does not recognize a managment entity
Andre,
OSEM will fill in the data one of three ways.
1) From HPSIM 5.1 or greater if it is installed on the same server as OSEM and the Managed By drop down is set to managed by HPSIM. (Note this drop will only appear if HPSIM 5.1 or greater is present on this server)
2) OSEM receives an event from the server.
3) Managed system information was filled in using the OSEMmsio tool before OSEM was started.
So until one of the above occurs the data will not be filled.
Regards,
Bruce
OSEM will fill in the data one of three ways.
1) From HPSIM 5.1 or greater if it is installed on the same server as OSEM and the Managed By drop down is set to managed by HPSIM. (Note this drop will only appear if HPSIM 5.1 or greater is present on this server)
2) OSEM receives an event from the server.
3) Managed system information was filled in using the OSEMmsio tool before OSEM was started.
So until one of the above occurs the data will not be filled.
Regards,
Bruce
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP