- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Problems converting RAID0 -> RAID5 on RS/12FC
Disk Enclosures
1748213
Members
2947
Online
108759
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-06-2004 09:39 PM
07-06-2004 09:39 PM
Problems converting RAID0 -> RAID5 on RS/12FC
Hello,
I have an HP Netserver RS/12FC set up in dual active/direct connect cluster mode. FCArray has 2 logical drives defined in 2 virtual arrays: A0 - RAID0+1 (8x18.2GB) and A1 - RAID0 (3x18.2GB), plus one HotSpare drive. A0 has drives with target(SCSI)IDs [0-3, 9] on channel 0 and [10, 11, 15] on channel 1. A1 array has drives with target IDs [12-14] on channel 1. The HotSpare has target ID [8] on channel 0.
The problem: I need to convert A1 from RAID0 to RAID5 w/o affecting A0 (i.e. data on A0 must remain intact), but I can't find any information about how it may be done.
If you happen to know the steps necessary to perform what I want or where to find the information, please let me know.
Any help much appreciated.
--
Sincerely,
Oskar
I have an HP Netserver RS/12FC set up in dual active/direct connect cluster mode. FCArray has 2 logical drives defined in 2 virtual arrays: A0 - RAID0+1 (8x18.2GB) and A1 - RAID0 (3x18.2GB), plus one HotSpare drive. A0 has drives with target(SCSI)IDs [0-3, 9] on channel 0 and [10, 11, 15] on channel 1. A1 array has drives with target IDs [12-14] on channel 1. The HotSpare has target ID [8] on channel 0.
The problem: I need to convert A1 from RAID0 to RAID5 w/o affecting A0 (i.e. data on A0 must remain intact), but I can't find any information about how it may be done.
If you happen to know the steps necessary to perform what I want or where to find the information, please let me know.
Any help much appreciated.
--
Sincerely,
Oskar
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP