- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- RAID configuration using 4Si card and SC10 Array
Disk Enclosures
1753916
Members
7677
Online
108810
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-06-2001 11:51 PM
11-06-2001 11:51 PM
RAID configuration using 4Si card and SC10 Array
Hi,
In our N4000 server running HP-UX 11.0, we wanted to configure RAID (level 5). For this, we have the following on the Hardware side,
1. HP A5856A RAID 4Si PCI 4-Channel Ultra2 SCSI
Controller Card
2. SC10 Array(LVD Interface) with 2 Bus Controller Cards
3. 8*36 GB disks
4. VHDCI Ultra SCSI Cable and Terminators
In the Software side, we have
1. 4Si driver(iop_drv)
2. IRM software
3. 3 patches(as per 4Si Release Notes)
PHKL_22030, PHKL_22494, PHKL_22941
Is all the required software and hardware are there for going ahead with the RAID implementaion?
Also, whether its possible to have an alternate path access to the disks(or
to the VG's) in the SC10 array.
If so, how to configure the alternate path access in this particular SC10 case?.
Please guide me in the above case.
Thanks and Regards,
N.Harinath.
In our N4000 server running HP-UX 11.0, we wanted to configure RAID (level 5). For this, we have the following on the Hardware side,
1. HP A5856A RAID 4Si PCI 4-Channel Ultra2 SCSI
Controller Card
2. SC10 Array(LVD Interface) with 2 Bus Controller Cards
3. 8*36 GB disks
4. VHDCI Ultra SCSI Cable and Terminators
In the Software side, we have
1. 4Si driver(iop_drv)
2. IRM software
3. 3 patches(as per 4Si Release Notes)
PHKL_22030, PHKL_22494, PHKL_22941
Is all the required software and hardware are there for going ahead with the RAID implementaion?
Also, whether its possible to have an alternate path access to the disks(or
to the VG's) in the SC10 array.
If so, how to configure the alternate path access in this particular SC10 case?.
Please guide me in the above case.
Thanks and Regards,
N.Harinath.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP