- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Replace Y Battery in 12H
Disk Enclosures
1752350
Members
6157
Online
108787
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2003 02:16 AM
10-10-2003 02:16 AM
The display panel on a Model 12H disk array shows replace Y battery. We are almost finished using this server and array and would like to avoid an HP service call. What possible problems could we encounter if I don't get the battery replaced? The array has 2 controllers and the other batteries are fine.
Controller X:
Overall state = GOOD
Battery #0 state = GOOD
Battery #1 state = GOOD
DRAM #0 state = GOOD
NVRAM #0 state = GOOD
NVRAM #1 state = GOOD
Controller Y: Overall state = GOOD
Battery #0 state = DEAD
Battery #1 state = GOOD
DRAM #0 state = GOOD
NVRAM #0 state = GOOD
NVRAM #1 state = GOOD
Thanks.
Controller X:
Overall state = GOOD
Battery #0 state = GOOD
Battery #1 state = GOOD
DRAM #0 state = GOOD
NVRAM #0 state = GOOD
NVRAM #1 state = GOOD
Controller Y: Overall state = GOOD
Battery #0 state = DEAD
Battery #1 state = GOOD
DRAM #0 state = GOOD
NVRAM #0 state = GOOD
NVRAM #1 state = GOOD
Thanks.
testing is for wimps.....
Solved! Go to Solution.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2003 03:26 AM
10-10-2003 03:26 AM
Solution
If controller X fails, then you would be treading on dangerous ground with only 1 good battery in controller Y. If as you say you are almost finished with the server and array, then I woulnd't worry about it too much. Incedentally, if controller X were to fail, you could always shutdown the array and move the good batteries over from X to Y.
-Josh
-Josh
What are the chances...
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP