Disk Enclosures
1748288 Members
3331 Online
108761 Solutions
New Discussion

Re: SA-P400 NCQ Support

 
nomadsole
Advisor

SA-P400 NCQ Support

I have a SA-P400 with hardware Rev B / firmware 4.12. However ADU shows "SATA NCQ Supported: FALSE". Do I need a later hardware rev to get NCQ work? What rev do I need?
2 REPLIES 2
Sameer_Nirmal
Honored Contributor

Re: SA-P400 NCQ Support

It maybe a case that the SATA drives being used in your setup are not NCQ compatible.

Take a look at the link below which says
"For NCQ to be enabled, it must be supported and turned on in the controller and in the hard drive itself."

http://h18004.www1.hp.com/products/quickspecs/12400_div/12400_div.html


The supported HP SATA hard drives which are NCQ compatible could be found at
http://h18000.www1.hp.com/products/quickspecs/11940_div/11940_div.HTML
Cyford
Occasional Advisor

Re: SA-P400 NCQ Support

I am  forced searching for the same answers,  the controller says my drives  support it and is enables on them,  but it disables them for my raid ,  How do i force it to enable on the controller itself?

 



[root@CyfordSan-00 ~]# hpacucli
HP Array Configuration Utility CLI 9.40.12.0
Detecting Controllers...Done.
Type "help" for a list of supported commands.
Type "exit" to close the console.

=> ctrl all show config detail

Smart Array 642 in Slot 0 (Embedded)
   Bus Interface: PCI
   Slot: 0
   Serial Number: P9226AN9SW804Y
   RAID 6 (ADG) Status: Disabled
   Controller Status: OK
   Hardware Revision: B
   Firmware Version: 2.80
   Post Prompt Timeout: 0 secs
   Cache Board Present: True
   Cache Status: Not Configured
   Total Cache Size: 64 MB
   Total Cache Memory Available: 32 MB
   No-Battery Write Cache: Disabled
   Battery/Capacitor Count: 0
   SATA NCQ Supported: False



Smart Array P400 in Slot 1
   Bus Interface: PCI
   Slot: 1
   Serial Number: PA2240J9STS3MR
   Cache Serial Number: PA82C0J9VVZ1OI
   RAID 6 (ADG) Status: Enabled
   Controller Status: OK
   Hardware Revision: B
   Firmware Version: 7.24
   Rebuild Priority: Medium
   Expand Priority: Medium
   Surface Scan Delay: 15 secs
   Surface Scan Mode: Idle
   Wait for Cache Room: Disabled
   Surface Analysis Inconsistency Notification: Disabled
   Post Prompt Timeout: 0 secs
   Cache Board Present: True
   Cache Status: OK
   Cache Ratio: 25% Read / 75% Write
   Drive Write Cache: Enabled
   Total Cache Size: 256 MB
   Total Cache Memory Available: 208 MB
   No-Battery Write Cache: Enabled
   Cache Backup Power Source: Batteries
   Battery/Capacitor Count: 1
   Battery/Capacitor Status: Failed (Replace Batteries)
   SATA NCQ Supported: False

   Array: A
      Interface Type: SATA
      Unused Space: 0  MB
      Status: OK
      Array Type: Data



      Logical Drive: 1
         Size: 29.8 GB
         Fault Tolerance: 0
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 7655
         Strip Size: 128 KB
         Full Stripe Size: 128 KB
         Status: OK
         Caching:  Enabled
         Unique Identifier: 600508B100104A39535453334D520002
         Disk Name: /dev/cciss/c0d0
         Mount Points: /boot 298 MB
         OS Status: LOCKED
         Logical Drive Label: A0002286PA2240J9STS3MRA8E1
         Drive Type: Data

      physicaldrive 1I:1:8
         Port: 1I
         Box: 1
         Bay: 8
         Status: OK
         Drive Type: Data Drive
         Interface Type: SATA
         Size: 32.0 GB
         Firmware Revision: 1.6     
         Serial Number: 1A29I3J662R163PBI526
         Model: ATA     OCZ-ONYX        
         SATA NCQ Capable: True
         SATA NCQ Enabled: True
         PHY Count: 1
         PHY Transfer Rate: 1.5Gbps


   Array: B
      Interface Type: SATA
      Unused Space: 0  MB
      Status: OK
      Array Type: Data



      Logical Drive: 2
         Size: 931.5 GB
         Fault Tolerance: 5
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 64 KB
         Full Stripe Size: 128 KB
         Status: Recovering, 73% complete
         Caching:  Enabled
         Parity Initialization Status: Initialization Failed
         Unique Identifier: 600508B100104A39535453334D520003
         Disk Name: /dev/cciss/c0d1
         Mount Points: / 8.0 GB
         OS Status: LOCKED
         Logical Drive Label: A0004EEFPA2240J9STS3MR2999
         Drive Type: Data

      physicaldrive 2I:1:1
         Port: 2I
         Box: 1
         Bay: 1
         Status: Rebuilding
         Drive Type: Data Drive
         Interface Type: SATA
         Size: 500 GB
         Firmware Revision: AX001A  
         Serial Number:            83JTPT5ZT
         Model: ATA     TOSHIBA MQ01ABD0
         SATA NCQ Capable: True
         SATA NCQ Enabled: True
         Current Temperature (C): 34
         Maximum Temperature (C): 36
         PHY Count: 1
         PHY Transfer Rate: 1.5Gbps

      physicaldrive 2I:1:2
         Port: 2I
         Box: 1
         Bay: 2
         Status: OK
         Drive Type: Data Drive
         Interface Type: SATA
         Size: 500 GB
         Firmware Revision: AX001A  
         Serial Number:            83JTPT5YT
         Model: ATA     TOSHIBA MQ01ABD0
         SATA NCQ Capable: True
         SATA NCQ Enabled: True
         Current Temperature (C): 34
         Maximum Temperature (C): 36
         PHY Count: 1
         PHY Transfer Rate: 1.5Gbps

      physicaldrive 2I:1:3
         Port: 2I
         Box: 1
         Bay: 3
         Status: OK
         Drive Type: Data Drive
         Interface Type: SATA
         Size: 500 GB
         Firmware Revision: AX001A  
         Serial Number:            83JTPT5XT
         Model: ATA     TOSHIBA MQ01ABD0
         SATA NCQ Capable: True
         SATA NCQ Enabled: True
         Current Temperature (C): 33
         Maximum Temperature (C): 36
         PHY Count: 1
         PHY Transfer Rate: 1.5Gbps