- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: SC10 DISK ARRAY --DIRECT CONNECT
Disk Enclosures
1752218
Members
11184
Online
108785
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-03-2002 07:04 AM
тАО09-03-2002 07:04 AM
SC10 DISK ARRAY --DIRECT CONNECT
Hi,
i have connected sc10 disk array to L class system directly using the single scsi card and sinfgle cable , i have terminated the other three connecters .But i am able to see
0/0/1/0.15.0 ctl HP A5272A
my dip switch settings are switch 1,3,4,5 are in 0 positioin and switch 2 in 1 .Plus tray id is 0 as i have only one sc10.But i am not able to see the disks ..any cluues
i have connected sc10 disk array to L class system directly using the single scsi card and sinfgle cable , i have terminated the other three connecters .But i am able to see
0/0/1/0.15.0 ctl HP A5272A
my dip switch settings are switch 1,3,4,5 are in 0 positioin and switch 2 in 1 .Plus tray id is 0 as i have only one sc10.But i am not able to see the disks ..any cluues
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-03-2002 03:35 PM
тАО09-03-2002 03:35 PM
Re: SC10 DISK ARRAY --DIRECT CONNECT
Well the SC10 is an LVD device and the card in the L is an Ultra2 SCSI. While these two are compatible, every device on the bus should be the same (LVD or SE). What I am not sure is what the internal drives are (LVD or SE). also take into consideration the internal SCSI ID's of these drives. If the settings on the SC10 are conflicting then there will be problems.
Unless of course you are running on its own seperate card with no other devices attached...
-bob
Unless of course you are running on its own seperate card with no other devices attached...
-bob
----------------
Was this helpful? Like this post by giving me a thumbs up below!
Was this helpful? Like this post by giving me a thumbs up below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-03-2002 09:31 PM
тАО09-03-2002 09:31 PM
Re: SC10 DISK ARRAY --DIRECT CONNECT
Hello,
Try to put switches 3,4 and 5 to 1 as well. Also, if you want full bus mode, you have to put switch 1 to 1 as well.
HTH,
Vince
Try to put switches 3,4 and 5 to 1 as well. Also, if you want full bus mode, you have to put switch 1 to 1 as well.
HTH,
Vince
Tape Drives RULE!!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-03-2002 09:32 PM
тАО09-03-2002 09:32 PM
Re: SC10 DISK ARRAY --DIRECT CONNECT
Hello,
Try to put switches 3,4 and 5 to 1 as well. Also, if you want full bus mode, you have to put switch 1 to 1 as well.
HTH,
Vince
Try to put switches 3,4 and 5 to 1 as well. Also, if you want full bus mode, you have to put switch 1 to 1 as well.
HTH,
Vince
Tape Drives RULE!!!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP