- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Storage Array P2000 G3 iSCSI controller management...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
10-16-2014 03:37 AM
10-16-2014 03:37 AM
Storage Array P2000 G3 iSCSI controller management port connection failure
Hi all,
I'm experimenting a connectivity problem on the controller of my HP P2000 G3 iSCSI.
In detail, the storage array is a dual controller (bundle version TS251P006-02) with both controller management port configured for manual addressing mode. Both the ethernet ports are connected to Cisco Nexus 2248TP configured for auto negotiation / auto speed (cables are ok).
In this configuration I have controller A configured for "Auto Negotiation: Enabled", "Duplex Mode: Full", "Link Speed: 100mbps" with no problem. It's correctly connected and works well.
Controller B, instead, is inoperable and even if I force the same configuration of controller A ("Auto Negotiation: Enabled", "Duplex Mode: Full", "Link Speed: 100mbps"), looking at configuration (with "show network-parameters" command) it results with "Auto Negotiation: Disabled", "Duplex Mode: Half", "Link Speed: 10mbps".
The command "set network-parameters auto-negotiation enabled link-speed 100mbps controller b" looks going well, I get "Command completed succesfully", but the effect is null.
I tried also to restart the controller, but nothing is changed.
Do you have any suggestions?
Thanks and best regards.
Roberto
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-22-2014 10:53 AM
12-22-2014 10:53 AM
Re: Storage Array P2000 G3 iSCSI controller management port connection failure
From help set network-parameters:
You can also set link speed, auto-negotiation, and duplex-mode parameters to enable Ethernet switches to communicate with the storage system. These settings will persist if the Ethernet cable is disconnected and reconnected, but will revert to default values if the controller is removed from the enclosure. These settings affect only the network port of the controller on which this command is entered.
So log on to controller B and issue the command again (you don't need to specify a controller)
What I'm stuck on is setting them back to default after changing them.
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP